American Standard 2881 User Manual
9
SERVICE
INSTALL POP-UP DRAIN
7
1
2
A
3
4
5
10
11
12
8
G
D
E
6
7
F
C
9
Push Tail piece (11) down into Trap (C) (threaded end up).
Assemble Pivot Rod (9) as shown in Figure-4B. Notice the
position of the Concave Washer (G).
position of the Concave Washer (G).
Insert Pivot Rod (9) into Drain Body (10) and tighten Pivot
Nut (F).
Nut (F).
Thread Locknut (5), Washer (4) and Gasket (3) (Bevel side
up) onto Drain Body (10).
up) onto Drain Body (10).
Apply a bead of Putty (D) to underside of Flange (2).
Remove one end of Clip (8) from Pivot Rod (9) by squeezing
ends together while sliding.
Insert Pivot Rod (9) into second or third hole in Extension
Rod (7) and reassemble Clip (8).
ends together while sliding.
Insert Pivot Rod (9) into second or third hole in Extension
Rod (7) and reassemble Clip (8).
Adjust stopper height by repositioning Extension Rod (7) and
tightening Thumbscrew (6).
tightening Thumbscrew (6).
Feed Drain Body (10) up through Sink (A) and thread the
Flange (2) fully onto Drain Body (10).
Flange (2) fully onto Drain Body (10).
Tighten Locknut (5) firmly, keeping the pivot rod hole pointed
towards the back of the sink.
towards the back of the sink.
Drop Stopper (1) into Drain Body (10).
Position Extension Rod (7) onto Pop-Up Rod (E) and tighten
Thumbscrew (6).
Thumbscrew (6).
1-1/4"
FIGURE-4B:
Push TAILPIECE INSERT (12) into TAILPIECE (11) and push
TAILPIECE up and thread tightly into DRAIN BODY (10).
TAILPIECE up and thread tightly into DRAIN BODY (10).
F
8
CHECK DRAIN CONNECTIONS
1
2
3
Operate Lift Rod and fill lavatory with water. Check that
DRAIN STOPPER (1) makes a good seal and retains water
in lavatory. Adjust stopper height by repositioning Lift
Rod (2) and tightening Thumbscrew (3).
DRAIN STOPPER (1) makes a good seal and retains water
in lavatory. Adjust stopper height by repositioning Lift
Rod (2) and tightening Thumbscrew (3).
Release DRAIN STOPPER (1) and check all drain
connections and "P" trap for leaks. Tighten if necessary.
connections and "P" trap for leaks. Tighten if necessary.
10
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT
CLEAN WITH CLEAR WATER. DRY
WITH A SOFT COTTON FLANNEL
CLOTH.
CLEAN WITH CLEAR WATER. DRY
WITH A SOFT COTTON FLANNEL
CLOTH.
DO NOT: CLEAN THE PRODUCT
WITH SOAPS, ACID, POLISH,
ABRASIVES, HARSH CLEANERS,
OR A CLOTH WITH A COARSE
SURFACE.
WITH SOAPS, ACID, POLISH,
ABRASIVES, HARSH CLEANERS,
OR A CLOTH WITH A COARSE
SURFACE.
"O" RING
M 9 6 8 2 1 1
To change direction of handle rotation,
proceed as follows:
proceed as follows:
Turn valve to OFF position.
Pull out INDEX CAP (1) and remove
HANDLE SCREW (2).
Pull off HANDLE (3), and unscrew
ESCUTCHEON (4).
Pull off STEM ADAPTER (7).
Remove SPRING CLIP (6).
Lift STOP WASHER (5), turn 90
Pull out INDEX CAP (1) and remove
HANDLE SCREW (2).
Pull off HANDLE (3), and unscrew
ESCUTCHEON (4).
Pull off STEM ADAPTER (7).
Remove SPRING CLIP (6).
Lift STOP WASHER (5), turn 90
°
and replace.
Replace SPRING CLIP (6) and STEM ADAPTER (7).
Reinstall ESCUTCHEON (4) and HANDLE
ASSEMBLY (1,2 & 3).
Reinstall ESCUTCHEON (4) and HANDLE
ASSEMBLY (1,2 & 3).
If spout drips, operate handles several times
from OFF to ON position. Do not force - handles
turn only 90
from OFF to ON position. Do not force - handles
turn only 90
°
.
90
°
5
6
2
4
3
7
1