Panasonic SC-BTT190 User Manual
44
VQT4D57
Messages
The following messages or service numbers may
appear on the TV or unit’s display.
appear on the TV or unit’s display.
Cannot play.
¾
¾
You inserted an incompatible disc.
Cannot play on this unit.
¾
¾
You tried to play a non-compatible image.
¾
Confirm “SD” on the unit’s display is not
displayed and re-insert the card.
displayed and re-insert the card.
No disc inserted.
¾
¾
The disc may be upside down.
$ This operation is not available.
¾
¾
Some operations are unsupported by the unit.
For example;
For example;
jBD-Video: During playback, reverse
slow-motion or reverse frame-by-frame is
not possible.
not possible.
IP address is not set.
¾
¾
The “IP Address” in “IP Address / DNS
Settings” is “---. ---. ---. ---”. Set the “IP
Address”, “Subnet Mask”, and “Gateway
Address”. (Select the automatic address
acquisition if necessary.)
Settings” is “---. ---. ---. ---”. Set the “IP
Address”, “Subnet Mask”, and “Gateway
Address”. (Select the automatic address
acquisition if necessary.)
The wireless access point currently has a low
network security setting. It is recommended to
change to a higher setting.
¾
network security setting. It is recommended to
change to a higher setting.
¾
Authentication type for the wireless LAN is set
to “Open system”, or the encryption type is
set to “No encryption”. It is recommended to
encrypt for safety reasons. For details, refer
to the instructions of the wireless router being
used. Encryption is required when playing
back video, etc., from DLNA compatible
devices.
to “Open system”, or the encryption type is
set to “No encryption”. It is recommended to
encrypt for safety reasons. For details, refer
to the instructions of the wireless router being
used. Encryption is required when playing
back video, etc., from DLNA compatible
devices.
F99
¾
¾
The unit fails to operate properly. Press [Í/I]
on the main unit for 3 seconds to switch the
unit to standby, then switch back on.
on the main unit for 3 seconds to switch the
unit to standby, then switch back on.
NET
¾
¾
While connecting to a network.
No PLAY
¾
¾
There is a viewing restriction on a BD-Video
or DVD-Video. (> 35)
or DVD-Video. (> 35)
No READ
¾
¾
The media is dirty or badly scratched. The
unit cannot play.
unit cannot play.
PLEASE WAIT
¾
¾
The unit is carrying out internal process. This
is not a malfunction. You cannot operate the
unit while “PLEASE WAIT” is displayed.
is not a malfunction. You cannot operate the
unit while “PLEASE WAIT” is displayed.
REMOVE
¾
¾
The USB device is drawing too much power.
Remove the USB device.
Remove the USB device.
SET
(“ ” stands for a number.)
¾
(“ ” stands for a number.)
¾
The remote control and main unit are using
different codes. Change the code on the
remote control.
Press and hold [OK]
and the indicated
number button at the
same time for more
than 5 seconds.
different codes. Change the code on the
remote control.
Press and hold [OK]
and the indicated
number button at the
same time for more
than 5 seconds.
U59
¾
¾
The unit is hot.
The unit switches to standby for safety
reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good ventilation when
installing the unit.
The unit switches to standby for safety
reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good ventilation when
installing the unit.
On the television
On the unit’s display
SC-BTT190GNGSGA-VQT4D57_mst.book 44 ページ ２０１２年１月１２日 木曜日 午前９時５９分