Yamaha RX-SL100RDS User Manual
52
TROUBLESHOOTING
Problem
Cause
Remedy
Refer to
page
The sound suddenly
goes off.
goes off.
The protection circuit has been activated
because of a short circuit, etc.
because of a short circuit, etc.
Check that the impedance selector setting is correct.
Check the speaker wires are not touching each other
and then turn this unit back on.
and then turn this unit back on.
—
The sleep timer has turned the unit off.
Turn on the power, and play the source again.
—
The sound is muted.
Press MUTE to cancel a mute.
Only the speaker on
one side can be
heard.
one side can be
heard.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
the cables may be defective.
Incorrect balance settings in the BASIC
menu.
menu.
Adjust the Speaker Level settings.
Only the center
speaker outputs
substantial sound.
speaker outputs
substantial sound.
When playing a monaural source with a
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
No sound from the
center speaker.
center speaker.
The output level of the center speaker is
set to minimum.
set to minimum.
Raise the level of the center speaker.
“Center” in the SOUND menu is set to
None.
None.
Select the appropriate mode for your center speaker.
One of the sound field programs (except
for 6ch Stereo) has been selected.
for 6ch Stereo) has been selected.
Select another sound field program.
No sound from the
surround speakers.
surround speakers.
The output level of the surround speakers
is set to minimum.
is set to minimum.
Raise the output level of the surround speakers.
“Surround L/R” in the SOUND menu is
set to None.
set to None.
Select the appropriate speaker mode for the surround
left and right speakers.
left and right speakers.
A monaural source is being played with
STEREO/EFFECT set to STEREO.
STEREO/EFFECT set to STEREO.
Press STEREO/EFFECT to turn on the sound fields.
Then select another sound field program.
Then select another sound field program.
—
No sound from the
surround back
speaker.
surround back
speaker.
“Surround L/R” in the SOUND menu is
set to None.
set to None.
If the speaker mode for the surround left and right
speakers is set to None, the speaker mode for the
surround back speaker is automatically set to None.
Select the appropriate speaker mode for the surround
left and right speaker mode.
speakers is set to None, the speaker mode for the
surround back speaker is automatically set to None.
Select the appropriate speaker mode for the surround
left and right speaker mode.
“Surround Back” in the SOUND menu is
set to None.
set to None.
Select Large or Small.
PLII/PLIIx is set to “PLII” when playing a
2-channel source.
2-channel source.
Select PLIIx. Press q/DTS to select a PLIIx sound
field program.
field program.
No sound from the
subwoofer.
subwoofer.
“LFE/Bass Out” in the SOUND menu is
set to FRONT when a Dolby Digital or
DTS signal is being played.
set to FRONT when a Dolby Digital or
DTS signal is being played.
Select SWFR or Both.
“LFE/Bass Out” in the SOUND menu is
set to SWFR or FRONT when a 2-channel
source is being played.
set to SWFR or FRONT when a 2-channel
source is being played.
Select Both.
The source does not contain low bass
signals.
signals.
01EN.00_RX-SL100RDS.book Page 52 Thursday, November 27, 2003 12:42 PM