Yamaha RX-V363 User Manual
56
En
Troubleshooting
Only the center
speaker outputs
substantial sound.
speaker outputs
substantial sound.
When playing a monaural source with a
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
No sound is heard
from the center
speaker.
from the center
speaker.
“CENTER” in “SPEAKER SET” is set to
“NONE”.
“NONE”.
Set “CENTER” to “SML” or “LRG”.
45
Some sound field programs do not output
sounds from the center speaker.
sounds from the center speaker.
Try another sound field program.
34
No sound is heard
from the surround
speakers.
from the surround
speakers.
“SUR. LR” in “SPEAKER SET” is set to
“NONE”.
“NONE”.
Set “SUR. LR” to “SML” or “LRG”.
45
This unit is in the “STRAIGHT” mode
and a monaural source is being played
back.
and a monaural source is being played
back.
Press LSTRAIGHT on the front panel so that
“STRAIGHT” disappears from the front panel
display.
“STRAIGHT” disappears from the front panel
display.
36
No sound is heard
from the subwoofer.
from the subwoofer.
“BASS OUT” in “SPEAKER SET” is set
to “FRNT” when a Dolby Digital or DTS
signal is being played.
to “FRNT” when a Dolby Digital or DTS
signal is being played.
Set “BASS OUT” to “SWFR” or “BOTH”.
46
“BASS OUT” in “SPEAKER SET” is set
to “SWFR” or “FRNT” when a 2-channel
source is being played.
to “SWFR” or “FRNT” when a 2-channel
source is being played.
Set “BASS OUT” to “BOTH”.
46
The source does not contain
low-frequency bass signals.
low-frequency bass signals.
Dolby Digital or DTS
sources cannot be
played. (Dolby Digital
or DTS indicator in
the front panel
display does not light
up.)
sources cannot be
played. (Dolby Digital
or DTS indicator in
the front panel
display does not light
up.)
The connected component is not set to
output Dolby Digital or DTS digital
signals.
output Dolby Digital or DTS digital
signals.
Make an appropriate setting following the operating
instructions for your component.
instructions for your component.
—
Audio input jack select is set to
“ANALOG”.
“ANALOG”.
Set Audio input jack select to “AUTO”.
31
A humming sound is
heard.
heard.
Incorrect cable connections.
Connect the audio cables firmly. If the problem
persists, the cables may be defective.
persists, the cables may be defective.
—
The volume level
cannot be increased,
or the sound is
distorted.
cannot be increased,
or the sound is
distorted.
You are attempting to set the volume level
higher than the maximum volume level.
higher than the maximum volume level.
Adjust “MAX VOL.” setting.
48
The component connected to the AUDIO
OUT (REC) jacks on this unit is turned
off.
OUT (REC) jacks on this unit is turned
off.
Turn on the power of the component.
—
The sound effect
cannot be recorded.
cannot be recorded.
It is not possible to record the sound effect
with a recording component.
with a recording component.
A source cannot be
recorded by an
analog component
connected to the
AUDIO OUT (REC)
jacks.
recorded by an
analog component
connected to the
AUDIO OUT (REC)
jacks.
The source component is not connected to
the analog AUDIO IN jacks on this unit.
the analog AUDIO IN jacks on this unit.
Connect the source component to the analog AUDIO
IN jacks.
IN jacks.
15, 17
The sound field
parameters and some
other settings of this
unit cannot be
changed.
parameters and some
other settings of this
unit cannot be
changed.
“MEM.GUARD” in “OPTION MENU” is
set to “ON”.
set to “ON”.
Set “MEM.GUARD” to “OFF”.
50
This unit does not
operate properly.
operate properly.
The internal microcomputer has been
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
Disconnect the power cable from the AC wall outlet
and then plug it in again after about 30 seconds.
and then plug it in again after about 30 seconds.
—
“CHECK SP WIRES”
appears in the front
panel display.
appears in the front
panel display.
Speaker cables are short-circuited.
Make sure all speaker cables are connected correctly.
11
Problem
Cause
Remedy
See
page
01EN_RX-V363_U.book Page 56 Friday, December 7, 2007 5:44 PM
Black process 45.0° 240.0 LPI