Pioneer VSX-1121-K User Manual

Page of 100
En
83
13
Additional information
About status messages
Refer to the following information when you come up with a status message while operating the 
Home Media Gallery.
Status messages
Descriptions
STARTING H.M.G.
A component on the network, including a PC, is currently being connected. 
Wait for a while.
Connection Down
The selected category or Internet radio station cannot be accessed.
File Format Error
Cannot be played back for some reasons.
Track Not Found
The selected song has not been found anywhere on the network.
Server Error
The selected server cannot be accessed.
Server Disconnected
The server has been disconnected.
empty
There are no files stored in the selected folder.
Preset Not Stored
The selected Internet radio station is not currently registered and saved.
Out of Range
The value entered is beyond the permitted range of the network settings.
License Error
The license for the contents to be played back is invalid.
Item Already Exists
This is displayed when the file you have attempted to register in the Favorites 
folder has already been registered.
Favorite List Full
This is displayed when you have attempted to register a file in the Favorites 
folder but the Favorites folder is already full.
Speaker Setting Guide
In order to achieve an even better surround 
effect, it is important to accurately position 
the speakers and make their volume and tone 
characteristics uniform so as to finely focus the 
multi-channel sound.
The three major elements in positioning the 
speakers are distanceangle and orienta-
tion
 (the direction in which the speakers are 
pointing).
Distance: The distance of all the speakers 
should be equal.
Angle: The speakers should be horizontally 
symmetrical.
Orientation: The orientation should be horizon-
tally symmetrical.
In most homes, however, it is not possible to 
achieve this environment. For the distance, on 
this receiver it is possible to automatically cor-
rect the speaker distance electrically to a preci-
sion of 0.5 inch using the Full Auto MCACC 
Setup function (page 25).
Step 1: Speaker layout and 
distance adjustment
Use speaker stands or the like to make sure the 
speakers are steady, and leave at least 10 cm 
(4 inches) from the surrounding walls. Position 
the speakers attentively so that the speakers on 
the left and right are at equal angles from the 
listening position (center of the adjustments). 
(We recommend using cords, etc., when adjust-
ing the layout.) Ideally all the speakers should 
be equidistant from the listening position.
 Note
!  If the speakers cannot be set at equal 
distances (on a circle), use the Auto MCACC 
Setup speaker distance correction and Fine 
Speaker Distance functions to make them 
equalize the distance artificially.
Step 2: Adjusting the speaker 
height
Adjust the heights (angles) of the different 
speakers.
Adjust so that the front speaker units reproduc-
ing mid- and high frequencies is roughly at the 
height of the ears.
If the center speaker cannot be set at the same 
height as the front speakers, adjust its angle of 
elevation to point it to the listening position.
Set surround speaker 1 so that it is not under 
the height of the ears.
Step 3: Adjusting the speaker 
orientation
If the left and right speakers are not pointing 
in the same direction, the tone will not be the 
same on the right and left, and as a result the 
sound field will not be reproduced properly. 
However, if all the speakers are pointed towards 
the listening position, the sound field will seem 
cramped. Testing by the Pioneer Multi-channel 
Research Group has shown that a good sense 
of sound positioning can be achieved by point-
ing all the speakers towards an area 30 cm to 80 
cm (12 inches to 31 inches) behind the listening 
position (between the surround speakers and 
the listening position).
However, the sense of sound positioning can 
differ according to the conditions in the room 
and the speakers being used. In smaller envi-
ronments in particular (when the front speakers 
are close to the listening position), with this 
method the speakers will be pointed too inward. 
We suggest you use this example of installation 
as reference when trying out different installa-
tion methods.