Pioneer VSX-1121-K User Manual

Page of 100
84
Step 4: Positioning and adjusting 
the subwoofer
Placing the subwoofer between the center 
and front speakers makes even music sources 
sound more natural (if there is only one sub-
woofer, it doesn’t matter if it is placed on the left 
or right side). The low bass sound output from 
the subwoofer is not directional and there is no 
need to adjust the height. Normally the sub-
woofer is placed on the floor. Put it in a position 
at which it will not cancel out the bass sound 
output from the other speakers. Also note that 
placing it near a wall may result in sympathetic 
vibrations with the building that could exces-
sively amplify the bass sound.
If the subwoofer must be installed near a wall, 
place it at an angle so that it is not parallel to 
the wall surface. This can help reduce any sym-
pathetic vibrations, but depending on the shape 
of the room this could result in standing waves. 
However, even if standing waves are generated, 
their influence on the sound quality can be 
prevented using the Auto MCACC’s standing 
wave control function (page 62).
Step 5: Default settings with the 
Auto MCACC Setup (auto sound 
field correction) function
It is more effective to perform the Full Auto 
MCACC Setup (page 25) procedure once 
the adjustments described above have been 
completed.
 Note
!  The distance to the subwoofer may be slightly 
larger than the distance actually measured 
with a tape measure, etc. This is because this 
distance is corrected for electric delay, and is 
not a problem.
Positional relationship between 
speakers and monitor
Position of front speakers and 
monitor
The front speakers should be as equidistant as 
possible to the monitor.
L
TV
R
45° to 60° 
Position of center speaker and 
monitor
Since mostly dialogs are output from the center 
speaker, keeping the center speaker as close 
as possible to the screen makes the overall 
sound more natural. For TVs using Braun tubes, 
however, when installing the center speaker on 
the floor, adjust its angle of elevation to point it 
towards the listening position.
Installation on floor
(Diagram as seen
    from the side)
Monitor
!  If the center speaker is not of the shielded 
type, install it away from the TV.
!  When installing the center speaker on top of 
the monitor, place it facing slightly downwards 
towards the listening position.
En
84
13
Additional information
Important information 
regarding the HDMI 
connection
There are cases where you may not be able to 
route HDMI signals through this receiver (this 
depends on the HDMI-equipped component 
you are connecting-check with the manufac-
turer for HDMI compatibility information).
If you aren’t receiving HDMI signals properly 
through this receiver (from your component), 
please try one of the following configurations 
when connecting up.
Configuration A
Use component video cables to connect the 
video output of your HDMI-equipped compo-
nent to the receiver’s component video input. 
The receiver can then convert the analog com-
ponent video signal to a digital HDMI signal for 
transmission to the display. For this configu-
ration, use the most convenient connection 
(digital is recommended) for sending audio to 
the receiver. See the operating instructions for 
more on audio connections.
 Note
!  The picture quality will change slightly during 
conversion.
Configuration B
Connect your HDMI-equipped component 
directly to the display using an HDMI cable. 
Then use the most convenient connection 
(digital is recommended) for sending audio 
to the receiver. See the operating instruc-
tions for more on audio connections. Set the 
display volume to minimum when using this 
configuration.
 Note
!  If your display only has one HDMI terminal, 
you can only receive HDMI video from the 
connected component.
!  Depending on the component, audio output 
may be limited to the number of channels 
available from the connected display unit (for 
example audio output is reduced to 2 channels 
for a monitor with stereo audio limitations).
!  If you want to switch the input function, you’ll 
have to switch functions on both the receiver 
and your display unit.
!  Since the sound is muted on the display when 
using the HDMI connection, you must adjust 
the volume on the display every time you 
switch input functions.
Cleaning the unit
!  Use a polishing cloth or dry cloth to wipe off 
dust and dirt.
!  When the surface is dirty, wipe with a soft 
cloth dipped in some neutral cleanser diluted 
five or six times with water, and wrung out 
well, and then wipe again with a dry cloth. Do 
not use furniture wax or cleansers.
!  Never use thinners, benzene, insecticide 
sprays or other chemicals on or near this unit, 
since these will corrode the surface.