Rotel RA-02 User Manual
9
12 Volt Trigger Outlet
[
Some audio components can be turned on
automatically when they receive a 12V turn
on “signal”. The 12V Trigger Outputs of the
RA-02 provide the required signal. Connect
compatible components to the RA-02 with a
conventional 3.5mm miniplug cable. When the
RA-02 is in Standby mode, the trigger signal
is interupted, so the components controlled by
it are turned off.
automatically when they receive a 12V turn
on “signal”. The 12V Trigger Outputs of the
RA-02 provide the required signal. Connect
compatible components to the RA-02 with a
conventional 3.5mm miniplug cable. When the
RA-02 is in Standby mode, the trigger signal
is interupted, so the components controlled by
it are turned off.
Troubleshooting
Most difficulties in audio systems are the result
of incorrect connections, or improper control
settings. If you encounter problems, isolate the
area of the difficulty, check the control settings,
determine the cause of the fault and make the
necessary changes. If you are unable to get
sound from the RA-02 refer to the suggestions
for the following conditions:
of incorrect connections, or improper control
settings. If you encounter problems, isolate the
area of the difficulty, check the control settings,
determine the cause of the fault and make the
necessary changes. If you are unable to get
sound from the RA-02 refer to the suggestions
for the following conditions:
Power Indicator Is Not Lit
The Power Indicator should be lit whenever the
RA-02 is plugged into the wall power outlet
and the Power Switch is pushed in. If it does
not light, test the power outlet with another
electrical device, such as a lamp. Be sure the
power outlet being used is not controlled by
a switch that has been turned off.
RA-02 is plugged into the wall power outlet
and the Power Switch is pushed in. If it does
not light, test the power outlet with another
electrical device, such as a lamp. Be sure the
power outlet being used is not controlled by
a switch that has been turned off.
Fuse Replacement
If another electrical device works when plugged
into the power outlet, but the Power Indicator
of the RA-02 does not light when plugged into
the same outlet and the Power Switch is pushed
in, it indicates that the internal power fuse may
have blown. If you believe this has happened,
contact your authorized Rotel dealer to get the
fuse replaced.
into the power outlet, but the Power Indicator
of the RA-02 does not light when plugged into
the same outlet and the Power Switch is pushed
in, it indicates that the internal power fuse may
have blown. If you believe this has happened,
contact your authorized Rotel dealer to get the
fuse replaced.
No Sound
Check the signal source to see if it is function-
ing properly. Make sure the cables from the
signal source to the RA-02 inputs are connected
properly. Be sure the Listening Selector is set
to the proper input. Check the wiring between
the RA-02 and the speakers.
ing properly. Make sure the cables from the
signal source to the RA-02 inputs are connected
properly. Be sure the Listening Selector is set
to the proper input. Check the wiring between
the RA-02 and the speakers.
Specifications
Continuous Power Output
40 watts/ch
(20-20 kHz, < 0.03%, 8 ohms)
Total Harmonic Distortion (20Hz-20kHz)
Total Harmonic Distortion (20Hz-20kHz)
< 0.03% at rated power, 1/2 power or 1 watt
Intermodulation Distortion (60 Hz : 7 kHz, 4:1) < 0.03% at rated power, 1/2 power or 1 watt
Frequency Response
Frequency Response
Phono Input
20Hz-15kHz, ±0.3dB
Line Level Inputs
10Hz-40kHz, ±1dB
Damping Factor (20-20,000 Hz, 8 ohms)
180
Input Sensitivity / Impedance
Phono Input
2.5mV / 47 kOhms
Line Level Inputs
150 mV / 24 kOhms
Input Overload
Phono Input
180mV
Line Level Inputs
5V
Premp Output / Impedance
1V / 470 Ohms
Tone Controls - Bass / Treble
±6 dB at 100Hz / 10kHz
Signal to Noise Ratio (IHF “A” weighted)
Phono Input
80 dB
Line Level Inputs
100 dB
Power Requirements
USA Version
120 Volts, 60 Hz
European Version
230 Volts, 50 Hz
Power Consumption
220 Watts
Dimensions (W x H x D)
435 x 72 x 342 mm
17
1
/
8
x 2
7
/
8
x 13
1
/
2
”
Panel Height
60 mm / 2
3
/
8
”
Weight (net)
5.9 kg, 13 lbs.
All specifications are accurate at the time of printing.
Rotel reserves the right to make improvements without notice.
Rotel reserves the right to make improvements without notice.
English