JVC 0209RYMMDWDAT User Manual

(on the System only)

Some countries space AM stations 9 kHz apart, and other countries use 10 kHz spacing. Before operating the tuner, select the 
appropriate AM tuner interval spacing used for your area.
•  You cannot change the AM tuner interval spacing while the ECO (Ecology) Mode is activated.

Select AM as the source.

Turn off (standby) the System.

Press and hold to change the AM tuner interval spacing.
 

Select FM or AM

Press repeatedly.
•  The selected frequency band appears.

Select a frequency

or

Press and hold for more than 2 seconds.
The System starts searching for stations and stops when a station of 
sufficient signal strength is tuned in.
•  Press during searching to stop.
•  Press repeatedly to change the frequency step by step.

Tune in to a preset station
•  For presetting stations, see 

below.

or

Press repeatedly to select its preset number.

Change the FM reception 
mode
(When an FM stereo 
broadcast is hard to receive)

Press to improve reception.
The 

 (mono) indicator lights up.

Stereo effect will be lost.
To restore the stereo effect, press again. The 

 (stereo) indicator lights up.

You can preset 30 FM and 15 AM stations manually.

Tune in to a station you want to preset.
•  You can also store the FM reception mode.

Press to activate the preset number entry mode.
•  Finish the following steps while the indication on the display is flashing.

or

Press to select a preset number for the station you want to store.

Press to store the station.

•  For the USB mass storage class device playback...
  – When connecting a USB mass storage class device, also 

refer to its manual.

  – Connect one USB mass storage class device to the System 

at a time. Do not use a USB hub.

  – This System is compatible with USB 2.0 Full Speed.
  – You can play back MP3/WMA files in a USB mass storage 

class device (maximum data transfer rate: 2 Mbps).

  – You cannot play back a file larger than 2 Gigabytes.
  – This System may not play back some USB mass storage 

class devices and does not support DRM (Digital Rights 
Management).

•  This System can recognize up to 255 groups in a disc. The 

total number of groups and tracks (in a disc) that can be 
recognized by the System is 512 (for MP3/WMA).

•  This System can recognize up to 99 groups and 999 tracks 

(with a maximum number of 255 tracks in a group) in a USB 
mass storage class device.

•  Prohibiting disc ejection (or canceling it) is not available 

when the display is turned off (“DISP OFF”) or the ECO Mode 
is activated (“ECO ON”) (see page 3).

 (see page 6)

•  You cannot set the clock and Daily Timer while the ECO 

(Ecology) Mode is activated.

•  The clock may gain or lose 1 to 2 minutes per month. If this 

happens, adjust the clock.

•  When you unplug the AC power cord or if a power failure 

occurs, the clock and the timer will be canceled. You need 
to set the clock first, then the timer again.

Timer Priority:
•  If you activate the Sleep Timer after Daily Timer starts 

playing the selected source, Daily Timer is canceled.

Digital Audio Player, etc.

OUTPUT POWER:
120 W (60 W + 60 W) at 8 Ω (10% THD)
Speakers/Impedance: 

8 Ω – 16 Ω

AUDIO IN: 500 mV/47 kΩ (at “NORMAL”)

 

250 mV/47 kΩ (at “HIGH”)

Digital input:   USB 

REC/PLAY

87.50 MHz – 108.00 MHz

531 kHz – 1 710 kHz (at 9 kHz 
spacing)

 

530 kHz – 1 710 kHz (at 10 kHz 
spacing)

80 dB

85 dB

Immeasurable

Compatible with USB 2.0 Full 
Speed

Mass storage class

Compatible file system:  FAT16, FAT32
Bus power supply: 

DC 5 V 

 500 mA

AC 110 V – 240 V 

, 50 Hz/60 Hz

36 W (power on)

 

5 W (standby mode)

 

1 W or less (ECO Mode)

165 mm x 250 mm x 272 mm
(W x H x D)

3.5 kg

Speaker units:   

4 cm cone x 1
12 cm cone x 1

 8 

Ω

140 mm x 250 mm x 183 mm 
(W x H x D)

1.8 kg each

Stereo mini plug cord 
(not supplied)

Turn the volume to minimum.

Press to select “AUDIO IN.”

Start playing the connected equipment.

Adjust the volume.

 (see page 3)

•  Pressing one of the source buttons also turns on the System 

and starts playing back if the source is ready or connected.

•  You cannot use the Sound Mode and Sound Turbo at the 

same time.

(see page 4)
•  This System cannot play “packet write” discs.
•  For MP3/WMA playback...
  – In this manual, “file” and “track” are interchangeably used.
  – This System can show the Tag data (Version 1).
  – MP3/WMA discs are required a longer readout time than 

regular CDs. (It depends on the complexity of the group/
file configuration.)

  – Some MP3/WMA files cannot be played back and will be 

skipped. This result from their recording processes and 
conditions.

  – When making MP3/WMA discs, use ISO 9660 Level 1 or 

Level 2 for the disc format.

  – This System can play back MP3/WMA files with the 

extension code <.mp3> or <.wma> (regardless of the 
letter case—upper/lower).

  –  It is recommended that you make each MP3/WMA file at 

a sampling rate of 44.1 kHz and at bit rate of 128 kbps. This 
System cannot play back files made at a bit rate of less 
than 64 kbps.

  – Playback order of MP3/WMA tracks may be different from 

the one you have intended while recording. If a folder 
(group) does not include MP3/WMA tracks, they are 
ignored.

•  Do not use the following USB mass storage class devices...
  – Whose rating is other than 5 V and exceeds 500 mA.
  – Equipped with special functions such as data security 

functions.

  – Divided by 2 or more partitions.

Play mode indicators (See page 4.)

Main display

A.STBY (Auto Standby) 
indicator (See page 6.)

HBS indicator (See page 3.)

Timer mode indicators 
(See page 6.)

SLEEP indicator 
(See page 6.)

File type indicators 
(See page 4.)

FM reception indicators 
(See page 5.)

Source indicator

S.TURBO (Sound Turbo) 
indicator (See page 3.)

Hard to listen to broadcasts because of noise.

\  Antenna connections are incorrect or loose.

\  The AM loop antenna is too close to the System.

\  The FM antenna is not properly extended and positioned.

\  Electrostatic discharge from your body may cause noise. If 

this happens, turn off and on the System again.

Unable to record into the USB device.

\  The capacity of the USB device is full. Erase some tracks.

\  You have recorded 999 tracks or groups on the USB mass 

storage class device. Erase unwanted tracks.

\  The USB mass storage class device is write-protected.

\  The USB mass storage class device you connected is 

incompatible to this System.

Display Messages for Recording Operations
NODEVICE
•  No USB mass storage class device is connected or 

the connected USB mass storage class device is not 
compatible with this System.

D. (data) FULL
•  The capacity of the USB mass storage class device is full.
FILEFULL
•  The USB mass storage class device has exceeded the 

maximum number of files it can support.

W. (write) PROT
•  The USB mass storage class device is write-protected.
SCMS VLT (violation)
•  You have tried to copy from a duplicated disc to the USB 

mass storage class device.

D. (device) FAIL
•  The System failed to read the USB mass storage class 

device.

Daily Timer does not work.

\  The System has been turned on when the on-time comes. 

Timer starts working only when the System is turned off.

If you are having a problem with your System, check this list 
for a possible solution before calling for service.

Power does not come on.

\  Power plug is not inserted securely. Plug in securely.
Adjustments or settings are suddenly canceled before you 
finish.

\  There is a time limit. Repeat the procedure again.
Operations are disabled.

\  The built-in microprocessor may malfunction due to 

external electrical interference. Unplug the AC power cord 
and then plug it back in.

Unable to operate the System from the remote control.

\  The path between the remote control and the remote 

sensor on the System is blocked.

\  The batteries are exhausted.
No sound is heard.

\  Speaker connections are incorrect or loose.

\  Headphones are connected.
The System does not work properly.

\  Many functions of this System are implemented by 

microcomputers. If the System does not work correctly, 
disconnect the AC power cord from the wall outlet, wait 
for a while, and connect the cord again.

The disc/USB mass storage class device does not play.

\  The disc is placed upside down. Place the disc with the 

label side up.

\  The USB mass storage class device is not connected 

properly.

MP3/WMA groups and tracks are not played back as you 
expect.

\  Playing order is determined when the groups and tracks 

were recorded. It depends on the writing application.

The disc/USB mass storage class device sound is 
discontinuous.

\  The disc is scratched or dirty.

\  MP3/WMA files have not been properly copied into the 

USB mass storage class device.

Sounds from USB mass storage class device are interrupted.

\  Noise and static electricity may stop the sound. In this 

case, disconnect and connect the USB mass storage class 
device again after turning off the System.

The disc tray does not open or close.

\  The AC power cord is not plugged in.

\  Disc ejection is prohibited (see page 4).

LVT1988-015B   EN_UX-GN5[UBUW]ff

•  It should be noted that it may be unlawful to re-record 

pre-recorded tapes, records, or discs without the consent 
of the owner of copyright in the sound or video recording, 
broadcast or cable program and in any literary, dramatic, 
musical, or artistic work embodied therein.

•  The recording level is not affected by the volume.
•  Hyper Bass Sound and Sound Turbo (see page 3) do not 

affect recordings.

•  You can record up to 999 tracks per group to the USB 

mass storage class device. If you try to record a track after 
recording 999 tracks, “FILEFULL” appears on the display 
and the track will not be recorded.

•  The tracks which are recorded to the USB mass storage 

class device will be converted into MP3 format (bit rate: 
128 kbps).

•  You cannot start recording into a USB mass storage class 

device while “READING” is shown on the display.

•  Do not disconnect a USB mass storage class device while 

playing or recording. It may cause malfunction.

•  During recording, the Random Play and Repeat Play will be 

cancelled.

The System uses the Serial Copy Management System which 
allows only first-generation digital copies to be made of 
premastered software such as regular CDs.
If you try to record from a duplicated disc into the USB mass 
storage class device, “SCMS VLT” appears on the display.

Press to start recording.

Both recording and playback start at the 
same time.
When playback ends, recording also stops.

•  If you have programmed the playing order for CD (see 

“Programming the Playing Order—Program Play” on page 
4), the tracks are recorded in the programmed order if 
Program Play is activated.

•  To stop recording manually, press 

7.

Press to start recording while playing 
back the track to record.

You can erase tracks/groups on the USB mass storage class 
device.
•  Once the tracks are erased, you cannot recover them.
•  To quit erasing, press 

7.

Select a track/group you want to erase while playback 
is stopped. (See page 4.)

or

Select the target to erase.

TTL DEL:

Delete a track.

GRP DEL: Delete a group.

DEL ALL: Delete all tracks.

or

DEL NO:

Cancel erasure.

DEL YES: Continue erasure.

Without setting the built-in clock, you cannot use Daily Timer.
•  To go back to the previous step, press CANCEL.

Press to activate the clock 
setting mode.

Adjust the hour, then the 
minute.

Press repeatedly to specify the time (in minutes) 
as follows:

The SLEEP indicator lights up and the display 
dims.

To check the remaining time until the System shuts off, 
press SLEEP once.

(only for Disc/USB)

Press to activate the Auto Standby.
•  The A.STBY indicator lights up.
•  The A.STBY indicator starts flashing after 

playback stops.

  If no operation is done for about 3 minutes, 

the System turns off. 

To cancel this function, press the button again.

Using Daily Timer, you can wake up with your favorite music.
•  You can store three Daily Timer settings; however, you can 

activate only one of the Daily Timers.

•  To correct a misentry during the process, press CANCEL. You 

can return to the previous step.

Press repeatedly to select one of the timer 
you want to set—TIMER-1, TIMER-2, or 
TIMER-3.

Canceled

or

1   Adjust the hour then the minute for 

on-time.

2   Adjust the hour then the minute for 

off-time.

3   Select the playback source—“TUNER 

FM,” “TUNER AM,” “AUDIO IN,” “DISC,” or 
“USB HOST.”

4   For “TUNER FM” or “TUNER AM”: 

Select a preset channel.*

 

For “DISC” or “USB HOST”: Select a 
track. (For MP3/WMA: Select the group, 
then the track number.)

5   Select the volume.

Turn off the System (on standby).
•  When the on-time comes, the System 

starts playing the specified source and 
sets the volume gradually to the preset 
level.

*  If no preset channel is stored, “NOMEMORY” appears. When the 

To exit from the timer setting, press TIMER as required.

1

Press repeatedly to select “TIMER-1,” 
“TIMER-2,” or “TIMER-3.”

2

To turn on the Daily Timer again, select one of the timer 
settings by pressing TIMER, then press SET.

REC indicator
(See page 6.)

2nd generation

1st generation

(On the System)

To get the best performance of the System, keep your discs 
and mechanism clean.

Handling discs
•  Remove the disc from its case by holding it at the edge 

while pressing the center hole lightly.

•  Do not touch the shiny surface of the disc, or bend the 

disc.

•  Put the disc back in its case after use.
•  Be careful not to scratch the surface of the disc when 

placing it back in its case.

•  Avoid exposure to direct sunlight, temperature extremes, 

and moisture.

To clean the disc:
•  Wipe the disc with a soft cloth in a straight line from center 

to edge.

Cleaning the System
•  Stains should be wiped off with a soft cloth. If the System is 

heavily stained, wipe it with a cloth soaked in water-diluted 
neutral detergent and wrung well, then wipe clean with a 
dry cloth.

•  Since the System may deteriorate in quality, become 

damaged or get its paint peeled off, be careful about the 
following:

  – DO NOT wipe it with a hard cloth.
  – DO NOT wipe it strongly.
  – DO NOT wipe it with thinner or benzine.
  – DO NOT apply any volatile substance such as insecticides 

to it.

  – DO NOT allow any rubber or plastic to remain in contact 

for a long time.

JVC bears no responsibility for any loss of data in USB mass 
storage class device while using this System.

Microsoft and Windows Media are either registered 
trademarks or trademarks of Microsoft Corporation in the 
United States and/or other countries.

(canceled)

Source indicators

To audio output (or 
headphone out, etc.)

or

SOUND indicator
(See page 3.)

You can record tracks digitally from a CD onto the USB mass 
storage class device.
•  Do not vibrate the System while recording tracks. It may 

damage the recorded tracks.

If the sound from the equipment connected to the AUDIO 
IN jack is too loud or too quiet, you can change the audio 
input level through the AUDIO IN jack (without changing the 
volume level).

Press repeatedly to select the level as follows:

NORMAL:

Ordinary input level.

HIGH:

Increases the input level.