Clarion DXZ385USB User Manual
English
13
DXZ385USB
6. OPERATIONS
Note:
• Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 6.
• Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 6.
Basic Operations
CAUTION
Be sure to lower the volume before
switching off the unit power or the ignition
key. The unit remembers its last volume
setting. If you switch the power off with the
volume up, when you switch the power back
on, the sudden loud volume may hurt your
hearing and damage the unit.
switching off the unit power or the ignition
key. The unit remembers its last volume
setting. If you switch the power off with the
volume up, when you switch the power back
on, the sudden loud volume may hurt your
hearing and damage the unit.
Turning on/off the power
Note:
• Be careful about using this unit for a long time
• Be careful about using this unit for a long time
without running the engine. If you drain the car’s
battery too far, you may not be able to start the
engine and this can reduce the service life of the
battery.
battery too far, you may not be able to start the
engine and this can reduce the service life of the
battery.
1. Press the [SRC] button.
2. The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
operation mode and will automatically switch
to display that mode.
3. Press and hold the [SRC] button for 1
second or longer to turn off the power for the
unit.
unit.
Note:
• System check
• System check
The first time this unit is turned on after the wire
connections are completed, it must be checked
what equipment is connected. When the power
is turned on, the “S-CHECK” appears in the
display, then the unit returns to the clock display
mode. The system check starts within the unit.
Then press the [SRC] button again, the unit turn
to the radio mode.
connections are completed, it must be checked
what equipment is connected. When the power
is turned on, the “S-CHECK” appears in the
display, then the unit returns to the clock display
mode. The system check starts within the unit.
Then press the [SRC] button again, the unit turn
to the radio mode.
Selecting a mode
1. Press the [SRC] button to change the
operation mode.
2. Each time you press the [SRC] button, the
operation mode changes in the following
order:
order:
Radio ➜ (Satellite radio) ➜ CD/MP3/WMA/
AAC ➜ USB/MTP/iPod ➜ (CD changer) ➜
(DVD changer) ➜ (TV) ➜ AUX ➜ Radio...
AAC ➜ USB/MTP/iPod ➜ (CD changer) ➜
(DVD changer) ➜ (TV) ➜ AUX ➜ Radio...
∗
External equipment not connected with
CeNET is not displayed.
CeNET is not displayed.
∗
iPod/MTP can connect to this unit via USB
SLOT.
SLOT.
Adjusting the volume
1. Turning the [ROTARY] knob clockwise
increases the volume; turning it
counterclockwise decreases the volume.
counterclockwise decreases the volume.
∗
The volume level is from 0 (minimum) to 33
(maximum).
(maximum).
Switching the display
Press the [DISP] button to select the desired
display.
display.
∗
Once selected, the preferred display becomes the
display default. When a function adjustment such
as volume is made, the screen will momentarily
switch to that function’s display, then revert back
to the preferred display several seconds after the
adjustment.
display default. When a function adjustment such
as volume is made, the screen will momentarily
switch to that function’s display, then revert back
to the preferred display several seconds after the
adjustment.
∗
If the button operation is performed with the
screen saver function on, the operation display
corresponding to the button operation is shown
for about 30 seconds and the display returns to
the screen saver display.
For details, refer to the subsection “Turning the
screen saver function on or off
screen saver function on, the operation display
corresponding to the button operation is shown
for about 30 seconds and the display returns to
the screen saver display.
For details, refer to the subsection “Turning the
screen saver function on or off
” in section
“Operations Common to Each Mode”.