Ariens 924128 ST1332LE User Manual
GB - 14
CONTROLS
AND FEATURES
See Figure 11 for all Controls and Features
locations.
locations.
Dual Handle Interlock
When Attachment Clutch and then Traction
Drive Clutch are engaged, the Attachment
Clutch will remain engaged (lever down) if
released. To stop attachment, release Traction
Drive Clutch and both clutches will disengage.
Drive Clutch are engaged, the Attachment
Clutch will remain engaged (lever down) if
released. To stop attachment, release Traction
Drive Clutch and both clutches will disengage.
Traction Drive Clutch - Left Hand
Lever
Lever
Squeeze the Traction
Drive Clutch Lever
against the Handlebar
(1) to engage wheel
drive for propelling unit.
Forward speed will vary
according to snow depth
and moisture content.
Release lever (2) to
stop movement.
Drive Clutch Lever
against the Handlebar
(1) to engage wheel
drive for propelling unit.
Forward speed will vary
according to snow depth
and moisture content.
Release lever (2) to
stop movement.
NOTE: When traveling to or from the area to
be cleared, press down on the handlebars
enough to raise the front of the unit slightly off
the surface. Engage the traction drive clutch
without engaging the attachment drive clutch.
be cleared, press down on the handlebars
enough to raise the front of the unit slightly off
the surface. Engage the traction drive clutch
without engaging the attachment drive clutch.
Attachment Clutch - Right Hand Lever
Squeeze Attachment
Clutch Lever against
handlebar (1) to engage
attachment. Release
both clutch levers (2) to
disengage power and
apply brake to
attachment.
Clutch Lever against
handlebar (1) to engage
attachment. Release
both clutch levers (2) to
disengage power and
apply brake to
attachment.
IMPORTANT: If the belt squeals when the
attachment clutch lever is engaged, the
attachment drive may be frozen. Immediately
release the attachment clutch lever and move
the unit into a heated area to thaw.
attachment clutch lever is engaged, the
attachment drive may be frozen. Immediately
release the attachment clutch lever and move
the unit into a heated area to thaw.
Ignition Switch (120V or 240V start on
engine)
engine)
Key Switch has two positions:
1. “Stop” - pulled out
1. “Stop” - pulled out
2. Run - pushed in
NOTE: DO NOT twist key after
it is inserted.
it is inserted.
Ignition Switch (12V start on dash
panel)
panel)
The ignition switch is
operated by a removable key.
It has three positions:
operated by a removable key.
It has three positions:
1. Stop
2. Run
2. Run
3. Start
Primer Bulb
Pushing the primer bulb in adds
fuel for easier engine start.
Refer to Starting and Shut Off.
fuel for easier engine start.
Refer to Starting and Shut Off.
Speed Selector
The Speed Selector controls the unit travel in a
forward or reverse direction when positioned
in notch of speed.
forward or reverse direction when positioned
in notch of speed.
Forward:
(6) Fastest
(1) Slowest
Reverse:
Reverse:
(1) Slow
(2) Fast
IMPORTANT: DO NOT
change motion from
forward to reverse with
clutch engaged.
Forward speed can be
changed without
declutching.
change motion from
forward to reverse with
clutch engaged.
Forward speed can be
changed without
declutching.
OPERATION
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
and understand the entire Safety
section before proceeding.
WARNING: To avoid injury to hands
and feet, always disengage clutches,
shut off engine, and wait for all
movement to stop before unclogging
or working on snow thrower.
Keep hands and feet away from auger
and impeller.
and feet, always disengage clutches,
shut off engine, and wait for all
movement to stop before unclogging
or working on snow thrower.
Keep hands and feet away from auger
and impeller.
1
2
OL2701
1
2
OL2691
1
2
OS1431
OS0232
1
2
3
OS1321
OS1192
1
2
6
5
4
3
2
1