Vocopro CLG-600 User Manual
Unpacking
6
As a part of our system of quality control, every Vocopro product is carefully inspected before leaving the factory
to ensure flawless appearance. After unpacking, please inspect for any physical damage. Save the shipping carton
and all packing materials, as they were carefully designed to reduce to minimum the possibility of transportation
damage should the unit again require packing and shipping. With your new CLG-600, you should have received
the following items:
to ensure flawless appearance. After unpacking, please inspect for any physical damage. Save the shipping carton
and all packing materials, as they were carefully designed to reduce to minimum the possibility of transportation
damage should the unit again require packing and shipping. With your new CLG-600, you should have received
the following items:
A standard IEC-320 AC inlet is provided on the rear panel of the CLG-600 to accept the detachable power cord
shipped with the unit. Units are pre-selected for 115 VAC, 60Hz and should be plugged into a standard NEMA 5-
15 3-wire grounded AC receptacle. For use of the unit outside the US, 230VAC, 50-60Hz power supplies are
required. The CLG-600 will perform normally from 100 to 125 VAC. An internal line fuse is used. In the event of
fuse failure, refer to a qualified service technician for servicing. Power consumption is 9 watts.
AC Power Requirements
The CLG-600 mounts in a standard 19-inch equipment rack. The mounting screw threads vary with different rack
manufactures and you should refer to your rack instructions for proper hardware. An oval head or flat head screw
with a plastic countersink washer is preferred to protect the finish of the CLG-600 under the screw. The CLG-600
is housed in a rugged steel case and can tolerate "in the field" abuse, however proper care will best suit the unit
for long-life and performance.
1. To mount, carefully place the CLG-600 in the desired rack space.
2. It is recommended to allow at least 4" of space deep in order to make cable connections easily.
3. Make sure all four holes are aligned evenly.
4. Using an alternating "X" rotation, screw mounting bolts in to ensure even tension and alignment.
Mounting Installation
MONO
DUAL CHANNEL COMPRESSOR
LIMITER WITH GATE
CLG-600
-30 20 -10 -5 -3 0 +3 +5
30 27 24 21 18 15 12 9 6 4 2 1
INAUDIBLE
INAUDIBLE
LEVEL
GAIN
LEVEL
OUT
IN
MANUAL
AUTO
RATIO
N1
THRESHOLD
dB
THRESHOLD
dB
THRESHOLD
dB
THRESHOLD
dB
MANUAL
AUTO
COMPRESSOR/LIMITER
RATIO
M1
ENHANCER
EXPANDER/GATE
RELEASE
Sec
O U P U T
dB
RELEASE
Sec
O U P U T
dB
CH 1
CH 2
30 27 24 21 18 15 12 9 6 4 2 1
GAIN
OUT
-30 20 -10 -5 -3 0 +3 +5
OFF
3
6
-20
+20
0
4
.05
0.5
200
2.5
0.1
2.5
1
1.5
8
msec
+20
+10
0
-10
-20
-30
-40
COMPRESSOR/LIMITER
ENHANCER
EXPANDER/GATE
-20
-35
-50
OFF
+10
0
-10
-35
-50
OFF
+10
0
-10
+20
+10
0
-10
-20
-30
-40
2.5
1
1.5
8
200
2.5
0.1
4
.05
0.5
-20
+20
0
OFF
3
6
-
+
-
+
msec
IN
STEREO
MODE
-35
TOP VIEW
UNPACKING
Rack Unit with Empty Space
CLG-600
AC Main's
Power Cable