Adtran MX412 User Manual
Menu Descriptions
MX410/MX412 System Manual
5-24 PRELIMINARY
61189500L1-1B
The Cross-Connect Mapping menu options are shown in
.
Table 5-10. Cross-Connect Mapping Menu Options
Option
Description
Function
1-24
DS0 1-24 connections
These options invoke the Change Cross-Connect Mapping menu
which is used to provision the cross-connect settings for the
selected DS1 port. Options are as follows:
which is used to provision the cross-connect settings for the
selected DS1 port. Options are as follows:
• 1. Choose TO Group (for DS1 1 through DS1 4/DS1 12)
• 2. Choose TO DS0: (enter a value)
• 3. Robbed Bit Signaling: select Enabled or Disabled
• 4. Apply Cross-Connect: applies the selections made from the
• 2. Choose TO DS0: (enter a value)
• 3. Robbed Bit Signaling: select Enabled or Disabled
• 4. Apply Cross-Connect: applies the selections made from the
Change Cross-Connect Mapping menu.
25
Map Multiple DS0's
This option invokes the Change Cross-Connect Mapping menu
which is used to provision the cross-connect settings for multiple
DS0s at the same time. Options are as follows:
which is used to provision the cross-connect settings for multiple
DS0s at the same time. Options are as follows:
• 1. Choose FROM DS0 Range: enter a range
• 2. Choose TO Group (for DS1 1 through DS1 4/DS1 12)
• 3. Choose TO DS0 Range: enter a range
• 4. Robbed Bit Signaling: select Enabled or Disabled
• 5. Apply Cross-Connect: applies the selections made from the
• 2. Choose TO Group (for DS1 1 through DS1 4/DS1 12)
• 3. Choose TO DS0 Range: enter a range
• 4. Robbed Bit Signaling: select Enabled or Disabled
• 5. Apply Cross-Connect: applies the selections made from the
Change Cross-Connect Mapping menu to all DS0s in the
range entered.
range entered.
Cross-Connect Mapping - Ports
1
PPPs
This option invokes the Change Cross-Connect Mapping menu,
which is used to provision the PPP ports. Options are as follows:
which is used to provision the PPP ports. Options are as follows:
• 1. Choose FROM PPP (for PPP 1 through PPP 4)
• 2. Choose TO Group (for DS1 1 through DS1 4)
• 3. Choose TO DS0 Range: enter a range
• 4. Apply Cross-Connect
• 2. Choose TO Group (for DS1 1 through DS1 4)
• 3. Choose TO DS0 Range: enter a range
• 4. Apply Cross-Connect
2
V.35
This option invokes the Change Cross-Connect Mapping menu,
which is used to provision the V.35 port. Options are as follows:
which is used to provision the V.35 port. Options are as follows:
• 1. Choose TO Group (for DS1 1 through DS1 4/DS1 12)
• 2. Choose TO DS0 Range: enter a range
• 3. Apply Cross-Connect
• 2. Choose TO DS0 Range: enter a range
• 3. Apply Cross-Connect
3
FXS (MX412 only)
This option invokes the Change Cross-Connect Mapping menu
which is used to provision the FXS port. Options are as follows:
which is used to provision the FXS port. Options are as follows:
• 1. Choose TO Group (for DS1 1 through DS1 12)
• 2. Choose TO DS0 Range: enter a range
• 3. Mode: Select Loop Start, PLAR D4, PLAR D3, or FX
• 2. Choose TO DS0 Range: enter a range
• 3. Mode: Select Loop Start, PLAR D4, PLAR D3, or FX
on page 4-9 for descriptions of
these options.
• 4. Apply Cross-Connect