Quatech ABDB-ET Series User Manual
Airborne Control Center
Page 38
AirborneDirect™ Ethernet Bridge User's Guide
100-8007-141G
Quatech, Inc. Confidential
Maximum Transmission Rate
Bridge’s maximum wireless transmission rate. The Bridge will
attempt the highest specified rate and fallback to a lower rate if
necessary. Default is 5.5 Mbps.
attempt the highest specified rate and fallback to a lower rate if
necessary. Default is 5.5 Mbps.
Network IP Settings
Enable DHCP Client
When checked, enables the Dynamic Host Configuration
Protocol (DHCP). For this parameter to work, the AP or
network must support DHCP.
Protocol (DHCP). For this parameter to work, the AP or
network must support DHCP.
DHCP Client Name
Bridge’s DHCP client name.
Enable DHCP Fixed Interval
Retransmission
Retransmission
Enables the interval value below.
DHCP Retransmit Interval
Configures the DHCP request retransmission interval (in
seconds) to use when the DHCP retransmission is set to fixed.
This is an integer with a range of 1-64.
Default is 15.
seconds) to use when the DHCP retransmission is set to fixed.
This is an integer with a range of 1-64.
Default is 15.
DHCP Acquire Time Limit
Configures the number of seconds that the Module should wait
to acquire its IP configuration using DHCP before applying the
DHCP fallback algorithm (if enabled).
This is an integer with a range of 1-255 seconds.
Default is 150.
Note: “0” will turn of IP Fallback.
to acquire its IP configuration using DHCP before applying the
DHCP fallback algorithm (if enabled).
This is an integer with a range of 1-255 seconds.
Default is 150.
Note: “0” will turn of IP Fallback.
Enable DHCP Fallback to fixed IP
Enables the DHCP fallback algorithm.
When the DHCP fallback algorithm is enabled, the Module will
apply the configuration from DHCP Fallback IP, Subnet,
and Gateway
When the DHCP fallback algorithm is enabled, the Module will
apply the configuration from DHCP Fallback IP, Subnet,
and Gateway
as the static IP configuration, if the DHCP
client has not received its IP configuration after DHCP
Acquire Time Limit
Acquire Time Limit
seconds.
unchecked = Disable DHCP fallback algorithm (default)
checked = Enable DHCP fallback algorithm
Enable DHCP Fallback to last
DHCP IP.
DHCP IP.
When enabled, use the last good DHCP IP address as the
fallback. Each time the IP address is successfully received via
DHCP, the fallback IP address is updated to use the new IP
address. It is *not* saved across reboots unless DHCP
Fallback Persist is also enabled. This setting is ignored if
DHCP Fallback is not enabled.
fallback. Each time the IP address is successfully received via
DHCP, the fallback IP address is updated to use the new IP
address. It is *not* saved across reboots unless DHCP
Fallback Persist is also enabled. This setting is ignored if
DHCP Fallback is not enabled.
Save current DHCP IP Address as
Fallback DHCP IP Address
Fallback DHCP IP Address
When the DHCP Fallback Auto address is updated, enabling
this setting causes the fallback IP address to be saved to
NVRAM, so that it is saved across reboots. This setting is
ignored if DHCP Fallback and DHCP Fallback Auto are not
enabled.
this setting causes the fallback IP address to be saved to
NVRAM, so that it is saved across reboots. This setting is
ignored if DHCP Fallback and DHCP Fallback Auto are not
enabled.
DHCP Fallback IP Address
Configures the IP address used by the DHCP fallback
algorithm.
Default is
algorithm.
Default is
192.168.10.1.