Panasonic pt-ae900e User Manual
Care
and
m
aintenance
E
NGLISH
-59
58-E
NGLISH
, Press and hold the ENTER
button for approximately 3
seconds.
seconds.
The “LAMP RUNTIME” will
change to “TIME RESET
[POWER OFF]”.
change to “TIME RESET
[POWER OFF]”.
B If the MENU button or the
RETURN button on the remote
control unit is pressed, the lamp
time resetting screen will be
cancelled.
control unit is pressed, the lamp
time resetting screen will be
cancelled.
- Turn off the power.
This will reset the cumulative
usage time for the lamp unit to
zero.
Refer to page 28 for details on
how to turn off the power.
usage time for the lamp unit to
zero.
Refer to page 28 for details on
how to turn off the power.
' Install the lamp unit cover, and
then use a Phillips screwdriver
to securely tighten the lamp
unit cover fixing screws.
to securely tighten the lamp
unit cover fixing screws.
( Insert the mains plug into the
mains socket and then press
the MAIN POWER switch.
the MAIN POWER switch.
) Press the POWER button so
that a picture is projected onto
the screen.
the screen.
* Press the MENU button to
display the menu screen, and
then press the F or G button
to select the “OPTION” menu.
then press the F or G button
to select the “OPTION” menu.
+ Press the ENTER button, and
then press the F or G button
to select “LAMP RUNTIME”.
to select “LAMP RUNTIME”.
NOTE:
B Be sure to install the lamp unit
B Be sure to install the lamp unit
and the lamp unit cover
securely. If they are not
securely installed, it may cause
the protection circuit to operate
so that the power cannot be
turned on.
securely. If they are not
securely installed, it may cause
the protection circuit to operate
so that the power cannot be
turned on.
Lamp unit replacement procedure
# Turn off the MAIN POWER
switch according to the
procedure given in “Turning off
the power” on page 28, and
then disconnect the mains plug
from the mains socket and
check that the area around the
lamp unit has cooled down.
procedure given in “Turning off
the power” on page 28, and
then disconnect the mains plug
from the mains socket and
check that the area around the
lamp unit has cooled down.
$ Use a Phillips screwdriver to
turn the lamp unit cover fixing
screws at the bottom of the
projector, and then remove the
lamp unit cover.
screws at the bottom of the
projector, and then remove the
lamp unit cover.
% Use a Phillips screwdriver to
loosen the two lamp unit fixing
screws until the screws turn
freely. Then hold the handle of
the lamp unit and gently pull it
out from the projector.
screws until the screws turn
freely. Then hold the handle of
the lamp unit and gently pull it
out from the projector.
& Insert the new lamp unit while
making sure that the direction
of insertion is correct, and then
use a Phillips screwdriver to
securely tighten the lamp unit
fixing screws.
When inserting the new lamp
unit, be sure to push it in at the
point A and B .
of insertion is correct, and then
use a Phillips screwdriver to
securely tighten the lamp unit
fixing screws.
When inserting the new lamp
unit, be sure to push it in at the
point A and B .
LAMP indicator
On-screen display
Illuminates red during
image projection and
standby mode.
image projection and
standby mode.
Displayed for 30
seconds. Pressing any
button will clear the
display.
seconds. Pressing any
button will clear the
display.
More than 2 700 hours*
Remains displayed until
any button is pressed.
any button is pressed.
More than 3 000 hours*
NOTE:
B If the lamp usage time has passed 3 000 hours (when “LAMP POWER” has been
B If the lamp usage time has passed 3 000 hours (when “LAMP POWER” has been
set to “HIGH” and when “DYNAMIC IRIS” has been set to “ON”), the projector will
switch to standby mode after approximately 30 minutes of operation. The steps
) to - on the next page should thus be completed within 30 minutes.
switch to standby mode after approximately 30 minutes of operation. The steps
) to - on the next page should thus be completed within 30 minutes.
Lamp unit cover
Lamp unit cover fixing screws
Handle
Lamp unit fixing screws
A
B
* These periods of time may become shorter according to the settings of the projector.