Texas Instruments TMS320DM357 User Manual
4.59 Control Status Register for Peripheral Transmit Endpoint (PERI_TXCSR)
Registers
www.ti.com
The Control Status Register for Peripheral Transmit Endpoint (PERI_TXCSR) is shown in
and
described in
.
Figure 74. Control Status Register for Peripheral Transmit Endpoint (PERI_TXCSR)
15
14
13
12
11
10
9
7
Reserved
ISO
MODE
DMAEN
FRCDATATOG
DMAMODE
Reserved
R-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R-0
6
5
4
3
2
1
0
CLRDATATOG
SENTSTALL
SENDSTALL
FLUSHFIFO
UNDERRUN
FIFONOTEMPTY
TXPKTRDY
W-0
R/W-0
R/W-0
W-0
R/W-0
R/W-0
R/W-0
LEGEND: R/W = Read/Write; R = Read only; W = Write only; -n = value after reset
Table 75. Control Status Register for Peripheral Transmit Endpoint (PERI_TXCSR)
Field Descriptions
Bit
Field
Value
Description
15
Reserved
0
Reserved
14
ISO
0-1
Set this bit to enable the Tx endpoint for Isochronous transfers, and clear this bit to enable the Tx
endpoint for Bulk or Interrupt transfers.
endpoint for Bulk or Interrupt transfers.
13
MODE
0-1
Set this bit to enable the endpoint direction as Tx, and clear this bit to enable it as Rx.
Note: This bit has any effect only where the same endpoint FIFO is used for both Transmit and
Receive transactions.
Receive transactions.
12
DMAEN
0-1
Set this bit to enable the DMA request for the Tx endpoint.
11
FRCDATATOG
0-1
Set this bit to force the endpoint data toggle to switch and the data packet to be cleared from the
FIFO, regardless of whether an ACK was received. This can be used by Interrupt Tx endpoints
that are used to communicate rate feedback for Isochronous endpoints.
FIFO, regardless of whether an ACK was received. This can be used by Interrupt Tx endpoints
that are used to communicate rate feedback for Isochronous endpoints.
10
DMAMODE
0-1
When using DMA, clear this bit to receive an interrupt for each packet, or set this bit to only
receive error interrupts.
receive error interrupts.
9-7
Reserved
0
Reserved
6
CLRDATATOG
0-1
Set this bit to reset the endpoint data toggle to 0.
5
SENTSTALL
0-1
This bit is set automatically when a STALL handshake is transmitted. The FIFO is flushed and the
TXPKTRDY bit is cleared. You should clear this bit.
TXPKTRDY bit is cleared. You should clear this bit.
4
SENDSTALL
0-1
Set this bit to issue a STALL handshake to an IN token. Clear this bit to terminate the stall
condition.
condition.
Note: This bit has no effect where the endpoint is being used for Isochronous transfers.
3
FLUSHFIFO
0-1
Set this bit to flush the next packet to be transmitted from the endpoint Tx FIFO. The FIFO pointer
is reset and the TXPKTRDY bit is cleared.
is reset and the TXPKTRDY bit is cleared.
Note: FlushFIFO has no effect unless TXPKTRDY is set. Also note that, if the FIFO is
double-buffered, FlushFIFO may need to be set twice to completely clear the FIFO.
double-buffered, FlushFIFO may need to be set twice to completely clear the FIFO.
2
UNDERRUN
0-1
This bit is set automatically if an IN token is received when TXPKTRDY is not set. You should
clear this bit.
clear this bit.
1
FIFONOTEMPTY
0-1
This bit is set when there is at least 1 packet in the Tx FIFO. You should clear this bit.
0
TXPKTRDY
0-1
Set this bit after loading a data packet into the FIFO. It is cleared automatically when a data packet
has been transmitted. An interrupt is generated (if enabled) when the bit is cleared.
has been transmitted. An interrupt is generated (if enabled) when the bit is cleared.
Universal Serial Bus (USB) Controller
122
SPRUGH3 – November 2008