Intel 1000LX User Manual
GB2.book : GB203 15 Tue Oct 27 13:01:06 1998
15
C H A P T E R
3
Configure the module and connect the cables
7
Repeat steps 2 through 6 for the second 1000Base Module,
ensuring that the cabling from this 1000Base Module goes to
the other Matrix Module.
ensuring that the cabling from this 1000Base Module goes to
the other Matrix Module.
8
Plug the SC connectors on the fiber optic cables into the RX and
TX sockets, and connect the other end of the cables to a device
or group of switches with redundancy.
TX sockets, and connect the other end of the cables to a device
or group of switches with redundancy.
9
Check the LEDs on the 1000Base Modules to verify the links.
For more information on LEDs, see Chapter 2
For more information on LEDs, see Chapter 2
Link Aggregation with Two Modules
Introduction
Two modules installed in a stack can be link aggregrated to increase
bandwidth between this stack and another device or stack.
bandwidth between this stack and another device or stack.
Prevent network loops
Link aggregation must be configured in Intel Device View to prevent
a loop. When two modules are installed in a stack and connected to
another single device or stack (without redundancy or link aggrega-
tion), then a loop may be created. Note that even with spanning tree
enabled, a delay of 10 to 15 seconds may occur before the loop is dis-
covered.
a loop. When two modules are installed in a stack and connected to
another single device or stack (without redundancy or link aggrega-
tion), then a loop may be created. Note that even with spanning tree
enabled, a delay of 10 to 15 seconds may occur before the loop is dis-
covered.
1
2
3
4
5
6
7
8
Power
Reset
Status
Temperature
RPS
Intel Express
550T Routing
550T Routing
Switch
Console
9600-8-N-1
Slot B
Port Status
Slot A
Stack Interface Module for 500 Series Switches
Stack Interface Module for 500 Series Switches
1
2
3
4
5
6
7
8
Power
Reset
Status
Temperature
RPS
Intel Express
550T Routing
Switch
550T Routing
Switch
Console
9600-8-N-1
Slot B
Port Status
Slot A
Stack Interface Module for 500 Series Switches
Stack Interface Module for 500 Series Switches
1
2
3
4
5
6
7
8
Power
Reset
Status
Temperature
RPS
Intel Express
550T Routing
Switch
Switch
Console
9600-8-N-1
Port Status
Slot A
Stack Interface Module for 500 Series Switches
1
2
3
4
7
8
Power
Reset
Status
Temperature
RPS
Intel Express
550T Routing
Switch
550T Routing
Switch
Console
9600-8-N-1
Port Status
Slot A
1740
1
2
3
4
5
6
7
8
Power
Reset
Status
Temperature
RPS
Intel Express
550T Routing
Switch
550T Routing
Switch
Console
9600-8-N-1
Slot B
Slot A
Port Status
Matrix Module for 500 Series Switches
4
1
5
2
6
3
Stack Interface Module for 500 Series Switches
1
2
3
4
5
6
7
8
Power
Reset
Status
Temperature
RPS
Intel Express
550T Routing
Switch
550T Routing
Switch
Console
9600-8-N-1
Slot B
Slot A
Port Status
Stack Interface Module for 500 Series Switches
Matrix Module for 500 Series Switches
4
1
5
2
6
3
Switches
Slot B
5
6
Slot B
Stack Interface Module for 500 Series
Primary
Secondary
3
4
5
6
Connects to
Matrix Module in
secondary switch
Matrix Module in
secondary switch
Connects to
Matrix Module in
primary switch
1000SX SST Module for 500 Series Switches
CLASS 1 LASER PRODUCT
1000Base-SX
Stack Interface Module
1000SX SST Module for 500 Series Switches
CLASS 1 LASER PRODUCT
1000Base-SX
Stack Interface Module