Sony MKS-2010 User Manual
Ch
apt
e
apt
e
r 2
N
a
mes
and
Fun
c
tions
of
P
of
P
a
rt
s
22
Control Panel Configuration
BORD (border): When this button is on, you can add
borders. The button lights in amber when no border
parameters have been assigned to the knobs in the
menu control block, and lights in green when they
have been assigned.
parameters have been assigned to the knobs in the
menu control block, and lights in green when they
have been assigned.
SOFT (soft edges): When this button is on, you can add
soft edges. The button lights in amber when no soft
edge parameters have been assigned to the knobs in the
menu control block, and lights in green when they
have been assigned.
edge parameters have been assigned to the knobs in the
menu control block, and lights in green when they
have been assigned.
CROP button: When this button is on, you can perform
cropping. The button lights in amber when no crop
parameters have been assigned to the knobs in the
parameters have been assigned to the knobs in the
menu control block, and lights in green when they
have been assigned.
have been assigned.
N/R (normal/reverse): When this button is on, it lights in
amber and the transition direction reverses every time
a transition finishes.
a transition finishes.
REV: When this button is on, it lights in amber and the
transition direction reverses.
POS (position) button: You can turn the positioner on
and use the joystick to move effect patterns in the x-
axis and y-axis directions, and to change their size.
axis and y-axis directions, and to change their size.
CTR (center) button: When the [POS] button is on,
pressing this button returns an effect pattern to the
default position and size.
default position and size.
Utility Control Block
a ENABLE/UTILITY operation buttons
You can assign utility commands to these buttons.
The following utility commands are assigned by default.
EDIT button: Enables and disables the switcher edit
You can assign utility commands to these buttons.
The following utility commands are assigned by default.
EDIT button: Enables and disables the switcher edit
mode.
GPI button: Enables and disables switcher GPI.
SAFE TITLE button: Turns on and off a marker showing
SAFE TITLE button: Turns on and off a marker showing
the television reception safe area and a cross marker
showing the center of the screen.
showing the center of the screen.
Blank button: No function assignment.
See “Utility Settings (Utility Menu)” (page 170) for more
information about how to assign arbitrary utility
commands to these buttons.
information about how to assign arbitrary utility
commands to these buttons.
b DEVICE/UTILITY operation buttons
You can assign utility commands to these buttons.
The following utility commands are assigned by default.
DEV1/DEV2: Selects the Device1/Device2 as control
You can assign utility commands to these buttons.
The following utility commands are assigned by default.
DEV1/DEV2: Selects the Device1/Device2 as control
target.
PLAY: Plays a tape or disk.
STOP: Stops a tape or disk.
ALL STOP: Stops tapes or disks on all devices.
CUE: Cue up.
START TC: Sets the current timecode as the start point.
SHTL: Turns shuttle mode on and off.
STOP: Stops a tape or disk.
ALL STOP: Stops tapes or disks on all devices.
CUE: Cue up.
START TC: Sets the current timecode as the start point.
SHTL: Turns shuttle mode on and off.
JOG: Turns jog mode on and off.
Note
When a delegation selection button is on, turning the
[SHTL] or [JOG] button on turns the delegation button off.
(The button pressed later receives priority).
[SHTL] or [JOG] button on turns the delegation button off.
(The button pressed later receives priority).
See “Utility Settings (Utility Menu)” (page 170) for more
information about how to assign arbitrary utility
commands to these buttons.
information about how to assign arbitrary utility
commands to these buttons.
EDIT
GPI
SAFE
TITLE
DEV1
JOG
DEV2
PLAY
STOP
ALL
STOP
CUE
START
TC
SHTL
DEVICE/UTILITY
ENABLE/UTILITY
1
ENABLE/UTILITY operation buttons
2
DEVICE/UTILITY operation buttons