DeLonghi 10.13 User Manual

19

the openings at the side 
for more than a minute 
(fig. 34).

4.    Extract the tank from the 

appliance and fill with 
water.

5.   Insert the filter in the 

water tank and immerse 
it completely for about 
ten minutes, sloping it to 
enable the air bubbles to 
escape (fig. 35).

6.  Insert the filter in the fil-

ter housing and press as 
far as it will go (fig. 36A) 

7.   Close the tank with the 

lid, then put the tank 
back in the machine (fig. 
36B).

When you install the filter, 
you must notify the appliance 
of its presence.
8.   Press the MENU/ESC button to enter the menu;
8.   Press the HOT MILK or LATTE button (fig. 8) until “Install 

filter” is displayed;

10.   Press the 

button;  

11.   The message “Enable?” is displayed.
12.   Press the

button to confirm the selection. “Hot 

water Confirm?” is displayed;

13.   Position a container under the hot water spout (min. ca-

pacity: 500 ml);

14.  Press the 

button to confirm the selection. The 

appliance begins hot water delivery and the message 
“Please wait” is displayed;

15.  After delivery, the appliance returns automatically to the 

“Ready for coffee” position. 

The new filter is active. You can now use the coffee maker. 

Replacing the filter
When “REPLACE FILTER” is displayed, after two months (see 
date indicator) or when the appliance has not been used for 3 
weeks, you should replace the filter:
1.   Extract the tank and exhausted filter;
2.   Take the new filter out of its packet and proceed as 

illustrated in points 2, 3, 4, 5 and 6 in the previous section.

3.   Position a container with a minimum capacity of 500 ml 

under the hot water spout.

4.   Press the MENU/ESC button to enter the menu; 
5.   Press the HOT MILK or LATTE button until “Replace filter 

“ is displayed.

6.   Press the 

 button;  

7.   The message “Confirm?” is displayed.
8.  Press the

 button to confirm the selection;   

9.   “Hot water… Confirm?” is displayed.
10.  Press the  

  button to confirm the selection. the 

appliance begins delivering hot water and the message 
“Please wait “ is displayed.  

11.  After delivery, the appliance returns automatically to the 

“ready for coffee” position. 

The new filter is now active and you can use the coffee maker. 

Removing the filter
If you want to continue using the appliance without a filter, 
you must remove it and notify the appliance of its removal as 
follows:
1.  Extract the tank and exhausted filter;
2.   Press the MENU/ESC button to enter the menu;
3.   Press the HOT MILK or LATTE button (fig. 8) until “Install 

filter Enabled” is displayed;

4.   Press the

 button

5.   “Disable?” is displayed; 
6.   Press the 

button to confirm and the MENU/ESC 

button to exit the menu.

Voltage:  

220-240 V~ 50/60 Hz max. 10A

Absorbed power:   

1450W

Pressure:  

15 bar

Water tank capacity:  

2.0 litres max.

Size Lxhxd:  

238x350x445 mm

Cable length:  

1.80 m

Weight:  

11.8  kg

Beans container capacity:  

250 g max.

The appliance complies with the following EC 

directives: 

•  EC Regulation 1275/2008 for standby;
•  Low  Voltage  Directive  2006/95/EC  and  subsequent

amendments;

•  EMC directive 2004/108/EC and subsequent amendments
•  Materials and accessories coming into contact with food

conform to eec regulation 1935/2004.

  

In compliance with European directive 2002/96/EC, 
the appliance must not be disposed of with hou-
sehold waste, but taken to an authorised waste se-
paration and recycling centre.