Sharp KB-3300JW User Manual

Page of 32
27
CLEANING AND CARE
•  Do not use the razor blade for daily cleaning as it may wear 
the pattern on the glass.
METAL MARKS OR BURNED ON RESIDUE  
Metal  marks  and  burned  on  residue  should  be  removed 
immediately after the cooktop has cooled. Metal marks can 
become permanent if not removed prior to future use.
1 Dampen a “scratchless” or “never scratch” pad that is safe 
for non-stick cookware.  The pattern and glass will be damaged 
if the pad is not damp or is soiled or if another type of pad is 
used. Apply a cleaner cream for glass ceramic cooktops.
2 Scrub to remove as much soil as possible.
3 Apply the cleaner cream over the soil, cover with a damp 
paper towel and let stand 30 minutes to 1 hour. Keep moist by 
covering the paper towel with plastic wrap.
4 Scrub again and wipe off with another clean, damp paper 
towel. Then wipe dry.
Note: 
•  Do not use aluminum foil on the cooktop.
•  If pots or pans of aluminum or copper are allowed to boil dry, 
permanent damage may affect the ceramic glass surface.
•  Do not slide pots and pans across the cooktop surface.
•  Cookware with rough bottoms can mark or scratch the 
cooktop surface.
•  Do not use a dull or nicked blade. Be sure to use a new, 
sharp razor scraper. 
MICROWAVE DRAWER   
 
INTERIOR 
 
Cleaning is easy because no heat is generated to the interior 
surfaces; therefore, there is no baking and setting of spills or 
spattering. To clean the interior surfaces, including drawer 
sealing surfaces, wipe with a soft damp cloth. DO NOT USE 
ABRASIVE  OR  HARSH  CLEANERS  OR  SCOURING 
PADS. For heavier soil, use mild soap; wipe clean with a soft 
damp cloth. Do not use any chemical oven cleaners.
MICROWAVE DRAWER GUIDES 
 
Remove the food crumbs from the Microwave Drawer guides. 
Wipe with a soft dry cloth in order to keep the Microwave 
Drawer opening and closing easily. 
WAVEGUIDE COVER   
ATTENTION
 The waveguide cover (located on the inside 
top of the microwave drawer area) is made from mica, so 
it requires special care.  Keep the waveguide cover clean 
to assure good microwave performance.  Carefully wipe 
with a soft damp cloth any food spatters from the surface 
of the cover immediately after they occur.  Built-up splashes 
may overheat and cause smoke or possibly catch fire.  Do 
not remove the waveguide cover.
ODOR REMOVAL
Occasionally, a cooking odor may remain in the Microwave 
Drawer. To remove, combine 1 cup water, grated peel and 
juice of one lemon and several whole cloves in a 2-cup glass 
measuring cup. Boil for several minutes using 100% power. 
Allow to set in the Microwave Drawer until cool. Wipe interior 
with a soft cloth.
OVEN  
 
CAUTION
  Before cleaning any part of the oven, be sure the 
oven is turned off. If not, press Stop/Clear.
Allow the oven to cool before cleaning.
INSIDE OF THE DOOR 
 
 
You do not need to clean the area inside the gasket by hand 
since the area is cleaned during the self-clean cycle.
Do not rub, clean or move the door gasket. Replace gasket 
when it is worn or frayed. 
The area outside the gasket and the door liner can be cleaned 
with a soap-filled steel wool or plastic pad, hot water and 
detergent. Rinse well with a vinegar and water solution.
INSIDE OF THE OVEN (SELF-CLEANING)
See page 24.
REMOVE AND REPLACE OVEN DOOR
1 Open the door to the fully opened position.
2 Pull the lock located on both hinge supports up and engage 
in the hook of the hinge levers. You may have to apply a little 
downward pressure on the door to pull the locks fully over 
the hooks.
3 Grab the door by the sides, pull the bottom of the door 
up and toward you to disengage the hinge supports. Keep 
pulling the bottom of the door toward you while rotating the 
top of the door toward the range to completely disengage the 
hinge levers.
4 Proceed in reverse to reinstall the door.
Make  sure  the  hinge  supports  are  fully  engaged  before 
unlocking the hinge levers.
CAUTION
 The door is very heavy. For safe, temporary storage, 
lay the door flat with the inside of the door facing down.
 
Lock in normal position.