Samsung SRP - 350 User Manual

Page of 35
 
 
 
 
User's Manual 
Ethernet Interface 
Rev. 4.00
 
SRP-270 
SRP-275 
SRP-350 
SRP-350plus 
SRP-370 / 372 
SRP-770 / 770II 
SLP-T400
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
http://www.samsungminiprinters.com
 

Summary of Contents of user manual for Samsung SRP - 350

  • Page 1User's Manual Ethernet Interface Rev. 4.00 SRP-270 SRP-275 SRP-350 SRP-350plus SRP-370 / 372 SRP-770 / 770II SLP-T400 http://www.samsungminiprinters.com
  • Page 2 Ethernet ■ Table of contents 1. Manual Information................................................................................................. 3 2. Interface card and available printer ....................................................................... 3 3. Specifications...
  • Page 3: 2. Interface card and available printer Ethernet 1. Manual Information The purpose of this manual is to provide information on the operation and usage instructions...
  • Page 4: 3-2. Configuration Tool Ethernet 3. Specifications 3-1. Hardware version Hardware version is marked on the label on the interface card bracket. Interface...
  • Page 5: 3-5. Details of interface card Ethernet 3-3. Virtual Driver - It converts output of Serial (COM) port into output of Ethernet (TCP/IP) port. -...
  • Page 6: 4. How to install Ethernet 4. How to install 1) Check the interface version [Note] - Each version uses its own Configuration Tool....
  • Page 7: 5-1. Configuration Tool Ethernet 5. Static IP interface set up 5-1. Configuration Tool 1) Turn on the printer. 2) Execute Configure Tool....
  • Page 8 Ethernet 4) Select MAC Address in Board list and set up Network Setting. MAC Address [Note] - If many...
  • Page 9 Ethernet 5) Enter value at Local Port. [Note] - Default value is 9100. Choose from 6000 to 10000. 6)...
  • Page 10 Ethernet 7) Set baud rate (Speed) at Serial Setting [Note] - The baud rate (Speed) should be same as...
  • Page 11 Ethernet 9) Click Exit to finish set up. V 4.00 - 11 -
  • Page 12: 5-2. Web Server Ethernet 5-2. Web Server 1) Execute Internet Explorer. 2) Enter IP address of the printer at Address of Internet...
  • Page 13 Ethernet [Note] - If you are not aware of Subnet Mask, refer to the below. - When the IP...
  • Page 14 Ethernet 6) Set baud rate (Serial speed). [Note] The baud rate (Speed) should be same as the baud rate...
  • Page 15 Ethernet 8) If you click the message, you can check your configuration setting. [Note] - If any change was...
  • Page 16 Ethernet (4) Check for newer version of stored pages → Click Every visit to the page. (5) Click Refresh...
  • Page 17: 6-1. Configuration Tool Ethernet 6. DHCP interface set up 6-1. Configuration Tool 1) Turn on the printer. 2) Execute Configure Tool. [Note]...
  • Page 18 Ethernet 4) Select MAC Address in Board list and check at DHCP Mode. MAC address [Note] - If many...
  • Page 19 Ethernet 6) When setting finishes, click Setting. [Note] Successfully finished set up Unsuccessfully finished set up - When setting...
  • Page 20 Ethernet 8) Click Search to check given IP. 9) If the given IP is OK, click Exit. V 4.00...
  • Page 21: 6-2. Web Server Ethernet 6-2. Web Server 1) Check at DHCP mode and click Apply. 2) Push the Function Key on the...
  • Page 22: 7-1. Configuration Tool Ethernet 7. Firmware update 7-1. Configuration Tool 1) Turn on the printer 2) Execute Configure Tool. [Note] - Use...
  • Page 23 Ethernet 4) Select MAC Address in Board. MAC Address [Note] - If many MAC addresses appear, refer to the...
  • Page 24 Ethernet [Note] - Check the extension of the file, which should be “bin”. Successfully finished F/W update Unsuccessfully finished...
  • Page 25: 7-2. Web Server Ethernet 7-2. Web Server 1) Click Firmware update. 2) Internet Explorer is executed and it moves to download site...
  • Page 26 Ethernet 3) Download Configure_Vx.xx.zip file and *.bin file. [Note] You can download it by double-clicking icons or copy and...
  • Page 27: 8. Ethernet test by using Windows test page Ethernet 8. Ethernet test by using Windows test page If you don’t have any test program to check printer’s...
  • Page 28 Ethernet 4) Select Ports tab. 5) Click Add Port. V 4.00 - 28 -
  • Page 29 Ethernet 6) Select Standard TCP/IP Port and click New port. 7) When standard TCP/IP printer add wizard window pops...
  • Page 30 Ethernet 9) Click Next. [Note] Click Next without any selection nor change. 10) Click Finish. 11) Click Close to...
  • Page 31 Ethernet 12) Click Configure Port. 13) Enter same port number as the value of Local Port of the Ethernet...
  • Page 32 Ethernet 14) Click OK. 15) Select General tab and click Print Test Page to check if the printer works...
  • Page 33: [Appendix 1] Printer DIP switch set up Ethernet [Appendix 1] Printer DIP switch set up Printer Baud rate & DSW set up Handshaking & Parity Baud...
  • Page 34: [Appendix 2] Function Key set up Ethernet [Appendix 2] Function Key set up 1. How to use (1) Turn on the printer (2) Wait 10...
  • Page 35: [Appendix 3] Factory Reset[Appendix 3] Factory Reset 1. Default setting after factory reset - Activate DHCP mode - Local Port: 9100 - Inactivity...