Manualsbrain.com
  1. Manuals
  2. Brands
  3. Mitsubishi
  4. WS-55517
  5. User Manual

Mitsubishi WS-55517 User Manual

Download
Page of 100
17
Connecting VCR Video and Audio to an Antenna or Wall Outlet 
Cable 
VCR to Antenna or Wall Outlet Cable 
Figure 5
A two-way RF splitter, 3 coaxial cables, right and left audio 
cables and S-Video or Video cables are required.  These are not 
included with the TV.
1.  Connect the incoming cable or Antenna to IN on the 
RF splitter. 
2.  Connect one coaxial cable from OUT on the RF 
splitter to ANTENNA IN on the VCR back panel.
3.  Connect one coaxial cable from OUT on the RF 
splitter to ANT-1 MAIN on the TV back panel.
4.  To use the TV speakers with the VCR, connect a 
set of audio cables from AUDIO OUT on the VCR 
back panel to INPUT 1 AUDIO-LEFT (MONO) and 
AUDIO-RIGHT on the TV back panel.  The red cable 
connects to the R (right) channel and the white 
cable connects to the L (left) channel.  If your VCR 
is mono (non-stereo), connect only the white (left) 
cable.
CableCARD
TM
SLOT
S-VIDEO
VIDEO
AUDIO-
LEFT/
T
T
(MONO)
AUDIO-
RIGHT
INPUT
MONITOR OUTPUT
AUDIO 2
1
2
O-
T/
T
T
O)
O-
T
DVI
Digita
Digita
S-Video
recommended
if available
Attach
only
one
cable
type
TV back panel
4.
–
(DTV/CABLE /VHF/UHF)
–
5.
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
INPUT
1
2
ANT-1
MAIN
MONITOR OUTPUT
AUDIO/VIDEO 1
7.
3.
6.
7.
HS-U748
VCR back panel
If your VCR has a video channel
or RF ON/OFF switch, set it to OFF.
5.
4.
5.
6.
2.
S-Video
recommended
if available
White
Red
White
Red
White
Red
W
h
i
t
e
R
e
d
Attach
only
one
cable
type
IN
OUT
OUT
TWO
W
A
Y
S
PLITTER
Incoming Cable
1.
2.
3.
Note:NetCommand® will assume your VCR is 
connected to inputs as shown here.  If you use any 
other inputs for your VCR or add a second VCR, this 
change must match in the NetCommand system.  
See Edit NetCommand... pages 35-42 for more 
information.
Figure 5.   Connecting a VCR to an Antenna or Wall Outlet Cable
5. Connect either an S-Video or Video cable from 
VIDEO OUT on the VCR back panel to INPUT 1 
VIDEO on the TV back panel.  Only one type of 
video cable should be connected.  S-Video is 
recommended, if available.
6.  For NetCommand® controlled recordings, connect 
a Video cable from VIDEO IN on the VCR back panel 
to MONITOR OUTPUT AUDIO/VIDEO 1 on the TV 
back panel.  
7.  Complete the NetCommand controlled recording 
connection by connecting a set of audio cables 
from AUDIO IN on the VCR back panel to MONITOR 
OUTPUT AUDIO/VIDEO 1 AUDIO-LEFT (MONO) and 
AUDIO-RIGHT on the TV back panel.  The red cable 
connects to the R (right) channel and the white cable 
connects to the L (left) channel.    
Additional connection cables are 
not provided with the TV.  They are 
available at most electronic stores.
IMPORTANT