Manualsbrain.com
  1. Manuals
  2. Brands
  3. Mitsubishi
  4. WS-55517
  5. User Manual

Mitsubishi WS-55517 User Manual

Download
Page of 100
18
VCR to a Cable Box
Figure 6 
A two-way RF splitter, 4 coaxial cables, right and left audio 
cables and an S-Video or Video cable are required.  These are 
not included with the TV.
1.  Connect the incoming cable to IN on the RF splitter.
2.  Connect one coaxial cable from OUT on the RF 
splitter to ANTENNA IN on the cable box back panel.
3.  Connect one coaxial cable from OUT on the RF 
splitter to ANT-2 AUX on the TV back panel.
4.  Connect one coaxial cable from OUT on the cable 
box to ANTENNA IN on the VCR back panel.
5.  Connect one coaxial cable from ANTENNA OUT on 
the VCR back panel to ANT-1 MAIN on the TV back 
panel.
6.  To use the TV speakers with the VCR, connect a 
set of audio cables from AUDIO OUT on the VCR 
back panel to INPUT 1 AUDIO-LEFT (MONO) and 
AUDIO-RIGHT on the TV back panel.  The red cable 
connects to the R (right) channel and the white 
Figure 6.  Connecting a VCR to a Cable Box
TA
T
T L
IO
CableCARD
TM SLOT
S-VIDEO
VIDEO
AUDIO-
LEFT/
T
T
(MONO)
AUDIO-
RIGHT
INPUT
MONITOR OUTPUT
AUDIO 2
1
2
Y
Pb
Pr
AUDIO-
LEFT/
T
T
MONO)
AUDIO-
RIGHT
S-Video
recommended
if available
Attach
only
one
cable
type
TV back panel
6.
5.
ANT-2
AUX
–
(DTV/CABLE /VHF/UHF) –
7.
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
INPUT
1
2
ANT-1
MAIN
IN
OUT
OUT
TWO
W
A
Y
SPLITTER
Incoming Cable
1.
2.
3.
MONITOR OUTPUT
AUDIO/VIDEO 1
9.
3.
8.
Cable Box
back panel
section
IN
OUT
2.
4.
9.
HS-U748
VCR back panel
If your VCR has a video channel
or RF ON/OFF switch, set it to OFF.
7.
6.
7.
8.
5.
4.
S-Video
recommended
if available
White
Red
White
Red
White
Red
W
h
i
t
e
R
e
d
Attach
only
one
cable
type
Note:  NetCommand® will assume your VCR is connected to inputs as shown here.  If you 
use any other inputs for your VCR or add a second VCR this change must match in the 
NetCommand system.  See Edit NetCommand... pages 35-42 for more information.
Connecting VCR Video and Audio to a Cable Box
cable connects to the L (left) channel.  If your VCR 
is mono (non-stereo), connect only the white (left) 
cable.
7.  Connect either an S-Video or Video cable from 
VIDEO OUT on the VCR back panel to INPUT 1 
VIDEO on the TV back panel.  Only one type of 
video cable should be connected.  S-Video is 
recommended, if available.
8.  For NetCommand® controlled recordings, connect 
a Video cable from VIDEO IN on the VCR back 
panel to MONITOR OUTPUT AUDIO/VIDEO 1 on 
the TV back panel.  
9.  Complete the NetCommand controlled recording 
connection by connecting a set of audio cables 
from AUDIO IN on the VCR back panel to MONITOR 
OUTPUT AUDIO/VIDEO 1 AUDIO-LEFT (MONO) 
and AUDIO-RIGHT on the TV back panel.  The red 
cable connects to the R (right) channel and the 
white cable connects to the L (left) channel.