Sony STR-DE898 Manual
masterpage:Left
lename[D:\Sony
SEM\Data_DE898_Revision3\J9050152_2580791113DE898U\2580791113\GB08REM_STR-
DE898-U.fm]
DE898-U.fm]
50
GB
model name1[STR-DE898]
[2-580-791-11(3)]
You can program the remote to control non-
Sony components by changing the code. Once
the control signals have been memorized, you
can use those components as part of your
system.
Furthermore, you can also program the remote
for Sony components that the remote is unable to
control. Note that the remote can only control
components that accept infrared wireless control
signals.
Sony components by changing the code. Once
the control signals have been memorized, you
can use those components as part of your
system.
Furthermore, you can also program the remote
for Sony components that the remote is unable to
control. Note that the remote can only control
components that accept infrared wireless control
signals.
1
Press AV
?/1
while holding down RM
SET UP.
The indicator lights up.
2
Press the input button (including TV
?/1
) for the component you want to
control.
For example, if you are going to control a
CD player, press SA-CD/CD.
CD player, press SA-CD/CD.
3
Press the numeric buttons to enter the
numeric code (or one of the codes if
more than one code exists)
corresponding to the component and
the maker of the component you want
to control.
numeric code (or one of the codes if
more than one code exists)
corresponding to the component and
the maker of the component you want
to control.
See the tables on pages 51–53 for
information on the numeric code(s)
corresponding to the component and the
maker of the component (the first digit and
the last two digits of the numeric code
correspond to the category and the maker’s
code respectively.)
information on the numeric code(s)
corresponding to the component and the
maker of the component (the first digit and
the last two digits of the numeric code
correspond to the category and the maker’s
code respectively.)
4
Press ENTER.
Once the numeric code has been verified,
the indicator slowly flashes twice and the
remote automatically exits the
programming mode.
the indicator slowly flashes twice and the
remote automatically exits the
programming mode.
5
Repeat steps 1 to 4 to control other
components.
components.
To cancel programming
Press RM SET UP during any step. The remote
automatically exits the programming mode.
automatically exits the programming mode.
To activate the input after
programming
programming
Press the programmed button to activate the
input you want.
input you want.
If programming is unsuccessful,
check the following:
check the following:
• If the indicator does not light up in step 1, the
batteries are weak. Replace both batteries.
• If the indicator flashes 4 times in quick
succession while entering the numeric code,
an error has occurred. Start again from step 1.
an error has occurred. Start again from step 1.
Notes
• The indicator turns off while a valid button is
pressed.
• In step 2, if several input buttons are pressed, only the
last pressed button is valid.
• In step 2, if you press TV ?/1, only TV VOL +/– ,
TV CH +/–, TV/VIDEO and WIDE buttons are
reprogrammed.
reprogrammed.
• In step 3, if an input button is pressed, the new input
is selected and the programming procedure returns to
the beginning of step 3.
the beginning of step 3.
• For the numeric codes, only the first three numbers
entered are valid.
To clear the memory of the
remote
remote
To clear all programmed and learned signals, do
the following to reset the remote to factory
settings.
the following to reset the remote to factory
settings.
Press
?/1
, AV
?/1
and MASTER VOL – at
the same time.
The indicator flashes 3 times, then goes off.
Programming the remote
GB01COV_STR-DE898-U.book Page 50 Tuesday, March 15, 2005 12:20 PM