ATTO Technology diamond array s User Manual
35
ATTO Technology Inc. Diamond Storage Array Installation and Operation Manual
5.5.3 Ethernet Commands
Ethernet configuration commands configure the Ethernet and TCP/IP parameters for the Diamond
Storage Array with an optional Ethernet management services card.
Storage Array with an optional Ethernet management services card.
EthernetSpeed
Specifies the speed of the Ethernet Network to which the
Diamond Storage Array is connected.
Specifies the speed of the Ethernet Network to which the
Diamond Storage Array is connected.
Choices are: [10|100 | Auto] where 10= 10 baseT, 100=
100 baseT
Default: auto
Set syntax: set EthernetSpeed [10 | 100| Auto]
Requires a SaveConfiguration command
Get syntax: get EthernetSpeed
100 baseT
Default: auto
Set syntax: set EthernetSpeed [10 | 100| Auto]
Requires a SaveConfiguration command
Get syntax: get EthernetSpeed
FTPPassword
Specifies a password of up to 32 characters for an FTP
session.
Specifies a password of up to 32 characters for an FTP
session.
Default: diamond
Set syntax: set FTPPassword
Requires a SaveConfiguration Restart command
Set syntax: set FTPPassword
Requires a SaveConfiguration Restart command
IPAddress
Specifies the IP Address of the Diamond Storage Array
on the Ethernet network. If DHCP is enabled, the
assigned address of the Diamond will be displayed.
Setting this value always modifies the internal NVRAM
value of the IP address.If IPDHCP is enabled (see below),
get command reports current IP address assigned by
DHCP server
Specifies the IP Address of the Diamond Storage Array
on the Ethernet network. If DHCP is enabled, the
assigned address of the Diamond will be displayed.
Setting this value always modifies the internal NVRAM
value of the IP address.If IPDHCP is enabled (see below),
get command reports current IP address assigned by
DHCP server
Default IP Address: 10.0.0.1
Set syntax: set IPAddress xxx.xxx.xxx.xxx
Requires a SaveConfiguration command
Get syntax: get IPAddress
Set syntax: set IPAddress xxx.xxx.xxx.xxx
Requires a SaveConfiguration command
Get syntax: get IPAddress
IPDHCP
Selecting DHCP allow the Diamond Storage Array to
request an IP address from the network. It requires that
the Diamond be attached to a network with at least one
DHCP server. The network must have at least one DHCP
server.
Selecting DHCP allow the Diamond Storage Array to
request an IP address from the network. It requires that
the Diamond be attached to a network with at least one
DHCP server. The network must have at least one DHCP
server.
Default: disabled
Set syntax: set IPDHCP [enabled | disabled]
Requires a SaveConfiguration command
Get syntax: get IPDHCP
Set syntax: set IPDHCP [enabled | disabled]
Requires a SaveConfiguration command
Get syntax: get IPDHCP
IPGateway
Specifies the IP Gateway for the Diamond Storage Array
on the Ethernet network. If IPDHCP is enabled (see
Specifies the IP Gateway for the Diamond Storage Array
on the Ethernet network. If IPDHCP is enabled (see
above), get command reports current IP gateway assigned
by DHCP server. Must conform to AAA.BBB.CCC.DDD
standard network IP addressing.
by DHCP server. Must conform to AAA.BBB.CCC.DDD
standard network IP addressing.
Default: 0.0.0.0
Set syntax: set IPGateway AAA.BBB.CCC.DDD
Requires a SaveConfiguration command
Get syntax: get IPGateway
Set syntax: set IPGateway AAA.BBB.CCC.DDD
Requires a SaveConfiguration command
Get syntax: get IPGateway
IPSubnetMask
Specifies the IP Subnet Mask for the Diamond Storage
Array on the Ethernet network. If DHCP is enabled, the
assigned subnet mask for the unit will be displayed.
Setting this value always modifies the internal NVRAM
value of the IP Subnet Mask.If IPDHCP is enabled (see
above), get command reports current subnet mask
assigned by DHCP server.
Specifies the IP Subnet Mask for the Diamond Storage
Array on the Ethernet network. If DHCP is enabled, the
assigned subnet mask for the unit will be displayed.
Setting this value always modifies the internal NVRAM
value of the IP Subnet Mask.If IPDHCP is enabled (see
above), get command reports current subnet mask
assigned by DHCP server.
Default: 255.255.255.0
Set syntax: set IPSubnetMask AAA.BBB.CCC.DDD
Requires a SaveConfiguration command
Get syntax: get IPSubnetMask
Set syntax: set IPSubnetMask AAA.BBB.CCC.DDD
Requires a SaveConfiguration command
Get syntax: get IPSubnetMask
SNMPTrapAddress
Sets up IP trap address and trap level.
Sets up IP trap address and trap level.
Default: 10.0.0.1
Set syntax: set SNMPTrapAddress [Index:1-6] [Address:
XXX.XXX.XXX.XXX] [Critical | Warning | All |
None]
Set syntax: set SNMPTrapAddress [Index:1-6] [Address:
XXX.XXX.XXX.XXX] [Critical | Warning | All |
None]
....................................
Requires a SaveConfiguration Restart command
Get syntax: get SNMPTrapAddress
Get syntax: get SNMPTrapAddress
SNMPTraps
Enables or disables SNMP traps.
Enables or disables SNMP traps.
Default: disabled
Set syntax: set SNMPTraps [enabled|disabled]
Requires a SaveConfiguration Restart command
Get syntax: get SNMPTraps
Set syntax: set SNMPTraps [enabled|disabled]
Requires a SaveConfiguration Restart command
Get syntax: get SNMPTraps
SNMPUpdates
Enables or disables the SNMP Management Information
Base (MIB) database.
Enables or disables the SNMP Management Information
Base (MIB) database.
Default: disabled
Set syntax: set SNMPTraps [enabled|disabled]
Requires a SaveConfiguration Restart command
Get syntax: get SNMPUpdates
Set syntax: set SNMPTraps [enabled|disabled]
Requires a SaveConfiguration Restart command
Get syntax: get SNMPUpdates