Yamaha RX-V3900 User Guide
126
En
Troubleshooting
No sound is heard
from the subwoofer.
from the subwoofer.
“Bass Out” in “Configuration” is set to
“Front” when a Dolby Digital or DTS
signal is being played.
“Front” when a Dolby Digital or DTS
signal is being played.
Set “Bass Out” to “SWFR” or “Front + SWFR”.
“Bass Out” in “Configuration” is set to
“SWFR” or “Front” when a 2-channel
source is being played.
“SWFR” or “Front” when a 2-channel
source is being played.
Set “Bass Out” to “Front + SWFR”.
The source does not contain low-
frequency signals.
frequency signals.
No sound is heard
from the surround
back speakers.
from the surround
back speakers.
“Surround Back” in “Configuration” is set
to “None”.
to “None”.
Check whether “Surround” is set to “Small” or
“Large” and configure “Surround Back” properly.
“Large” and configure “Surround Back” properly.
While this unit is in the CINEMA DSP 3D
mode, no sound is output at the surround
back speakers.
mode, no sound is output at the surround
back speakers.
The audio input
sources cannot be
played in the desired
digital audio signal
format (Desired input
source indicator or
decoder indicator in
the front panel
display does not light
up).
sources cannot be
played in the desired
digital audio signal
format (Desired input
source indicator or
decoder indicator in
the front panel
display does not light
up).
The connected component is not set to
output the desired digital audio signals.
output the desired digital audio signals.
Make an appropriate setting following the operating
instructions for your component.
instructions for your component.
—
Audio input jack select is set to
“ANALOG”.
“ANALOG”.
Set the audio input jack select to “AUTO”.
A humming sound is
heard.
heard.
Incorrect cable connections.
Connect the audio cables firmly. If the problem
persists, the cables may be defective.
persists, the cables may be defective.
—
No connection from the turntable to the
GND terminal.
GND terminal.
Connect the grounding cable of the turntable to the
GND terminal of this unit.
GND terminal of this unit.
The volume level is
low while a record is
being played.
low while a record is
being played.
The record is being played on a turntable
with an MC cartridge.
with an MC cartridge.
Connect your turntable to this unit through an MC-
head amplifier.
head amplifier.
The volume level
cannot be increased,
or the sound is
distorted.
cannot be increased,
or the sound is
distorted.
The component connected to the AUDIO
OUT (REC) jacks of this unit is turned
off.
OUT (REC) jacks of this unit is turned
off.
Turn on the power of the component.
—
A source cannot be
recorded by the
recording component.
recorded by the
recording component.
The audio source connected to the MULTI
CH INPUT jacks of this unit cannot be
recorded.
CH INPUT jacks of this unit cannot be
recorded.
A given input source is not output at the
same output channel (e.g. DVR IN to
DVR OUT).
same output channel (e.g. DVR IN to
DVR OUT).
Connect the recording component to another channel
that is not being used for connecting the source
component.
that is not being used for connecting the source
component.
You are trying to record a DTS source.
(DTS signal is a digital bitstream.
Attempting to record the DTS bitstream
digitally will result in noise being
recorded.)
(DTS signal is a digital bitstream.
Attempting to record the DTS bitstream
digitally will result in noise being
recorded.)
Make a setting so that the analog signal will be output
from your DTS-compatible player and then connect
the DTS-compatible player to the AUDIO IN jacks
while the recording component is connected to the
analog AUDIO OUT (DVR, VCR or MD/CD-R)
jacks.
from your DTS-compatible player and then connect
the DTS-compatible player to the AUDIO IN jacks
while the recording component is connected to the
analog AUDIO OUT (DVR, VCR or MD/CD-R)
jacks.
Problem
Cause
Remedy
See
page