Becker highspeed 7934 Operating Guide
23
>>>
GENERAL OPERATIONS
> US
On the windshield
If the dashboard is too far away from
the driver, the unit bracket can be fitted
directly to the windshield using the suc-
tion mechanism.
> If the adapter plate (4) is already secured
If the dashboard is too far away from
the driver, the unit bracket can be fitted
directly to the windshield using the suc-
tion mechanism.
> If the adapter plate (4) is already secured
at the foot (5), remove it. Pull the lever
(3) upward and remove the adapter
plate (4) downward for this purpose.
(3) upward and remove the adapter
plate (4) downward for this purpose.
> Find a suitable position.
> Press the base (5) with its suction sur-
> Press the base (5) with its suction sur-
face against the windshield.
> Rotate the unit bracket so that the sup-
port plate is roughly in the direction of
viewing required.
viewing required.
> Press the lever (3) downward.
The bracket will have stuck firmly to the
windshield. It can now be set precisely. To
remove, actuate the lever (3) again.
windshield. It can now be set precisely. To
remove, actuate the lever (3) again.
On the dashboard
An adapter plate is provided for mounting
on the dashboard. This is stuck onto the
dashboard. The mounting face may only
be slightly curved.
An adapter plate is provided for mounting
on the dashboard. This is stuck onto the
dashboard. The mounting face may only
be slightly curved.
> Find a suitable position.
> Remove the protective film from the
> Remove the protective film from the
lower contact surface of the adapter
plate (4). Press the adapter plate (4)
onto the instrument panel.
plate (4). Press the adapter plate (4)
onto the instrument panel.
> Take the unit holder, pull the lever (3)
upward and position the base (5) with
its suction surface into the upper con-
tact surface of the adapter (4).
its suction surface into the upper con-
tact surface of the adapter (4).
> Turn the unit holder such that the car-
rier plate is positioned roughly in the
desired viewing direction.
desired viewing direction.
> Press the lever (3) downwards.
The bracket will have stuck firmly to the
adapter. It can now be set precisely.
To remove, actuate the lever (3) again.
The bracket will have stuck firmly to the
adapter. It can now be set precisely.
To remove, actuate the lever (3) again.
Adjusting the unit bracket
The support plate (7) can be swung in two
directions (horizontally and vertically). It
can thereby be set at virtually every angle
of vision to the driver.
The support plate (7) can be swung in two
directions (horizontally and vertically). It
can thereby be set at virtually every angle
of vision to the driver.
NOTICE
Also ensure that there is enough space to
easily slide the Traffic Assist Highspeed
back out of the bracket.
Clean the mounting area on the wind-
shield or dashboard so that it is clean and
free of grease. Do not use smearing, soapy
cleaning agents, otherwise this may affect
how it sticks to the dashboard.
easily slide the Traffic Assist Highspeed
back out of the bracket.
Clean the mounting area on the wind-
shield or dashboard so that it is clean and
free of grease. Do not use smearing, soapy
cleaning agents, otherwise this may affect
how it sticks to the dashboard.
NOTICE
Please check local and state traffic laws as
some areas forbid mounting the unit on
the windshield.
some areas forbid mounting the unit on
the windshield.
Note:
If the adapter plate is removed, you may
find residue from the glue on your dash-
board.
If the adapter plate is removed, you may
find residue from the glue on your dash-
board.
Note:
Do not swing the support plate in both
directions at the same time! Before mov-
ing, always take the Traffic Assist High-
speed off the unit bracket.
Do not swing the support plate in both
directions at the same time! Before mov-
ing, always take the Traffic Assist High-
speed off the unit bracket.