Sonance ST2432D Installation Instruction
Page 3
ST2432D Series
960.066 Rev # 1
2. If the ceiling grid is a 15/16” T-Bar, remove the Tegular
Brackets from the SpeakerTile (see
Figure 1).
3. Hold the SpeakerTile with the fl at/front surface facing
down and insert it obliquely through the ceiling grid
until it passes entirely through. Remove protective
cardboard. See
until it passes entirely through. Remove protective
cardboard. See
Figure 3.
4. Maneuver the SpeakerTile until it is aligned and
centered to the grid. The SpeakerTile will rest by the
four Tegular Brackets (attached to the frame sides) on
a 9/16” ceiling grid and will rest by the Diaphragm on a
15/16” ceiling grid. See
four Tegular Brackets (attached to the frame sides) on
a 9/16” ceiling grid and will rest by the Diaphragm on a
15/16” ceiling grid. See
Figure 4.
9 / 1 6 ” C E I L I N G G R I D : T E G U L A R M O U N T
INSTALLATION WITHOUT BACKBOX
INSTALLATION WITHOUT BACKBOX
1. Adjust the four tegular brackets (attached to the
SpeakerTile frame, see
Figure 1) to the desired height
by loosening the screws and moving them up or down,
or by rotating the brackets 180 degrees and then
moving up or down, depending on the height required.
See
or by rotating the brackets 180 degrees and then
moving up or down, depending on the height required.
See
Figure 5.
2. Once the tegular brackets have been adjusted,
make sure they are straight (perpendicular) and then
fasten them properly to avoid further movement. If not
previously done, run speaker wires or conduit (as per local
Building Code requirements) into the selected mounting
location. Fasten and seal as required.
fasten them properly to avoid further movement. If not
previously done, run speaker wires or conduit (as per local
Building Code requirements) into the selected mounting
location. Fasten and seal as required.
Connect the speaker wires to the correct (+) and (–)
SpeakerTile terminals and select the required power
tap.
tap.
IMPORTANT: To avoid any noise or damage to the
system when in operation be sure speaker wires or
other objects are not in contact with the back of the
SpeakerTile surface. To avoid damage to the front
s u r f a c e d u r i n g m o u n t i n g d o n o t r e m o v e t h e
protective cardboard cover from the Speaker Tile until it has
been fully positioned into the ceiling.
system when in operation be sure speaker wires or
other objects are not in contact with the back of the
SpeakerTile surface. To avoid damage to the front
s u r f a c e d u r i n g m o u n t i n g d o n o t r e m o v e t h e
protective cardboard cover from the Speaker Tile until it has
been fully positioned into the ceiling.
3. Hold the SpeakerTile with the front surface (fl at) facing
down and insert it obliquely through the ceiling grid
until is passes entirely through. Remove protective
cardboard. See
until is passes entirely through. Remove protective
cardboard. See
Figure 3.
4. Maneuver the SpeakerTile until it is aligned and
centered to the grid. When properly installed, the tegular
brackets (attached to the frame of the SpeakerTile) will
rest on the ceiling grid system. See
brackets (attached to the frame of the SpeakerTile) will
rest on the ceiling grid system. See
Figure 6.
Figure 3
15
/
16
” Grid
9
/
16
” Grid
Figure 4
0 [0] Factory
5
/
32
”
[4.0]
5
/
16
”
[8.0] 180° Rotated
1
/
8
”
[3.0] 180° Rotated
Figure 5
Tegular
Bracket
Speaker
Frame
9
/
16
” Grid
Speaker
Diaphragm
Figure 6