Sonance ST2432D Installation Instruction
Page 4
ST2432D Series
960.066 Rev # 1
15/16” CEILING GRID: TEGULAR MOUNT
INSTALLATION WITHOUT BACKBOX
INSTALLATION WITHOUT BACKBOX
PLEASE NOTE: This mounting method requires
the diaphragm front surface to be factory-routed in
order to drop below the ceiling grid. If the supplied
SpeakerTiles have not been routed, this installation
method cannot be used.
the diaphragm front surface to be factory-routed in
order to drop below the ceiling grid. If the supplied
SpeakerTiles have not been routed, this installation
method cannot be used.
1. Remove the four tegular brackets attached to the sides
of the SpeakerTile frame. See
Figure 1 on page 2.
2. If not previously done, run speaker wires or conduit (as
per local Building Code requirements) into the selected
mounting location. Fasten and seal as required. Connect
the speaker wires to the correct (+) and (– ) SpeakerTile
terminals and select the required power tap. Insure that
all connections and wiring runs are in compliance with
required codes and regulations.
mounting location. Fasten and seal as required. Connect
the speaker wires to the correct (+) and (– ) SpeakerTile
terminals and select the required power tap. Insure that
all connections and wiring runs are in compliance with
required codes and regulations.
IMPORTANT: To avoid any noise or damage to the
system when in operation be sure speaker wires or
other objects are not in contact with the back of the
SpeakerTile surface. To avoid damage to the front
s u r f a c e d u r i n g m o u n t i n g d o n o t r e m o v e t h e
protective cardboard cover from the Speaker Tile until it has
been fully positioned into the ceiling.
system when in operation be sure speaker wires or
other objects are not in contact with the back of the
SpeakerTile surface. To avoid damage to the front
s u r f a c e d u r i n g m o u n t i n g d o n o t r e m o v e t h e
protective cardboard cover from the Speaker Tile until it has
been fully positioned into the ceiling.
3. Hold the SpeakerTile with the front surface (fl at) facing
down and insert it obliquely through the ceiling grid
until is passes entirely through. Remove protective
cardboard. See
until is passes entirely through. Remove protective
cardboard. See
Figure 3.
4. Maneuver the SpeakerTile until it is aligned and
centered to the ceiling grid. The SpeakerTile diaphragm
will rest on the ceiling grid system. See
will rest on the ceiling grid system. See
Figure 7.
9/16” AND 15/16” CEILING GRIDS: FLUSH
OR TEGULAR MOUNT INSTALLATION WITH
BACKBOX
OR TEGULAR MOUNT INSTALLATION WITH
BACKBOX
NOTE: Before attempting to install the SpeakerTile
you must fi rst assemble the backbox according to the
following instructions:
you must fi rst assemble the backbox according to the
following instructions:
UNPACKING AND INSPECTION
Carefully open the shipping cartons and remove all
contents. Inspect for damage. Repor t damage or
shortages to Sound Advance.
contents. Inspect for damage. Repor t damage or
shortages to Sound Advance.
Figure 8 indicates all items required for assembly of the
PBB2.0 backbox.
PBB2.0 backbox.
ASSEMBLING THE BACKBOX
1. Lay the four panels down on your work surface with the
bends facing up. Peel the covers from the adhesive
squares on each panel.
squares on each panel.
2. Set up the four corners as shown in
Figure 9 by aligning
the straight end of one with the bent end of the other
panel at a 45
panel at a 45
o
angle. Open the panels to form a 90
o
angle and insure that the adhesive tape bonds the ends
of the panels together.
of the panels together.
3. Fasten the two panels together using one of the long
sheet metal screws on the upper part of the panel as
15
/
16
”
Grid
Speaker
Frame
Frame
Speaker
Diaphragm
Diaphragm
Figure 7
Box Panel (4)
Long
Screw (8)
Screw (8)
Short
Screw (1)
Screw (1)
Latch (1)
Rivet (1)
Spacer (4)
Hinge (1)
Spring-Loaded
Hinge (1)
Figure 8
Figure 9