Tekkeon ET2000 User Guide
5
USER GUIDE
4
To Pair the Devices
1. Turn on the mobile phone and place it next to the headset.
2. Initiate the Bluetooth device-pairing (discovery) feature on the mobile phone. Refer to the mobile
phone user guide for instructions on initiating this feature.
3. With the headset turned off, press and hold the TALK button until the blue and amber LEDs flash
alternately or until you hear Pairing tone (approximately five seconds).
4. Release the TALK button. The headset is now in Pairing Mode.
5. Follow the mobile phone prompts, and when prompted for the passkey (also called passcode or
BT PIN), enter 0000 (the ezTalker mini passkey). When pairing is complete, the headset will be
placed in Standby Mode, ready to make and receive calls, the amber LED will turn off, and the
blue LED will flash at two-second intervals.
placed in Standby Mode, ready to make and receive calls, the amber LED will turn off, and the
blue LED will flash at two-second intervals.
To Cancel Pairing Mode
While you are in pairing mode, you can cancel the pairing process and turn off the headset.
1. While in pairing mode, press and hold the TALK button until both LEDs turn off or you hear the
Off tone (approximately three seconds).
To Connect to a Paired Device
1. Follow the menu on the paired device to connect to ezTalker mini. You must be disconnected
from all other paired devices if the headset is currently connected with any other device.
To Disconnect From a Paired Device
1. While connected to a paired device, follow the menu on the device to disconnect from ezTalker
mini.
Charging ezTalker mini
Before using ezTalker mini, you must charge the headset for approximately two hours. When fully
charged, the battery provides up to five hours of talk time and up to 120 hours of standby time.
charged, the battery provides up to five hours of talk time and up to 120 hours of standby time.
To Charge the Headset
1. Remove the rubber plug that covers the charging jack on the upper left side of the headset.
2. Plug the power adapter into the charging jack.
3. Plug the power adapter into a wall outlet. While the headset is
charging, the amber LED on the headset will remain on. When the
headset is fully charged, the amber LED will turn off.
headset is fully charged, the amber LED will turn off.
4. Unplug the power adapter from the wall outlet and the headset.
5. Place the rubber plug in the charging jack.
BATTERY INDICATION: When the battery is low (less than 10% of
capacity), the amber LED will flash and you’ll hear a beep every 32 seconds.
capacity), the amber LED will flash and you’ll hear a beep every 32 seconds.
Pairing ezTalker mini to Your Mobile Phone
Pairing is the process of linking the headset with your Bluetooth mobile phone or other Bluetooth
device that supports a headset and/or handsfree profile. Before using ezTalker mini with your
mobile phone you must pair the devices. After this process is complete, you can use the headset
with your paired mobile phone.
device that supports a headset and/or handsfree profile. Before using ezTalker mini with your
mobile phone you must pair the devices. After this process is complete, you can use the headset
with your paired mobile phone.
You can pair ezTalker mini with up to seven Bluetooth devices. Once each device is paired with
ezTalker, you must disconnect the paired phone or device to connect to a different phone or device.
While connected to a different paired device, ezTalker will not be connected to other paired
devices.
ezTalker, you must disconnect the paired phone or device to connect to a different phone or device.
While connected to a different paired device, ezTalker will not be connected to other paired
devices.
BEFORE YOU PAIR THE HEADSET, ENSURE THAT THE BATTERY IS FULLY CHARGED, AND REVIEW THE INSTRUCTIONS
IN YOUR MOBILE PHONE USER GUIDE FOR PAIRING YOUR MOBILE PHONE TO A BLUETOOTH HEADSET.
Figure 1.
Power adapter connected to
ezTalker mini.