Intermec 2400 Quick Setup Guide
11
10
6
Type the current date in the format YYYY/
MM/DD (year/month/date) and press {.
MM/DD (year/month/date) and press {.
7
Press ; to save the changes and exit the
Time and Date screen.
Time and Date screen.
8
Press d twice and choose OK.
If you are using the Wavelink Avalanche client
management system, you can quickly configure
the parameters for your terminal. For help, see
Chapter 2, “Configuring and Managing the
Terminals,” in the Trakker Antares 2400 Family
System Manual (P/N 071389).
management system, you can quickly configure
the parameters for your terminal. For help, see
Chapter 2, “Configuring and Managing the
Terminals,” in the Trakker Antares 2400 Family
System Manual (P/N 071389).
(Optional) Configure the
Serial Port Parameters
Serial Port Parameters
You can connect the terminal to a PC or
other RS-232 device with the TD2400
Communications Dock, the Trakker Antares
Optical Link Adapter, or the RS-232 scan
module adapter.
other RS-232 device with the TD2400
Communications Dock, the Trakker Antares
Optical Link Adapter, or the RS-232 scan
module adapter.
The values you set for the terminal’s serial port
must match the values set for the host computer’s
serial port.
must match the values set for the host computer’s
serial port.
Press ) y 2 4 8 to access the TRAKKER
Antares 2400 Menu System. Choose
Configuration Menu > Communications
Menu > Serial Port [COM1].
Antares 2400 Menu System. Choose
Configuration Menu > Communications
Menu > Serial Port [COM1].
Configure the 2425 Radio
and Network Parameters
and Network Parameters
Before you can use the 2425, you need to install
and configure each device in the RF network.
and configure each device in the RF network.
To configure the RF network
1
In a UDP Plus or WTP network, configure
the Intermec Gateway or DCS 30X. For
help, see the documentation that shipped
with your Intermec Gateway or your
DCS 30X user’s manual. In a TCP/IP
network, configure the host.
the Intermec Gateway or DCS 30X. For
help, see the documentation that shipped
with your Intermec Gateway or your
DCS 30X user’s manual. In a TCP/IP
network, configure the host.
2
Configure the access points. For help, see
your access point user’s manual.
your access point user’s manual.
3
Configure each Trakker Antares 2425
terminal. For help, see the next procedure.
terminal. For help, see the next procedure.
To configure the terminal
1
Press ) y 2 4 8 to access the
TRAKKER Antares 2400 Menu System.
Choose Configuration Menu >
Communications Menu > Primary
Network or Advanced Network or Radio.
TRAKKER Antares 2400 Menu System.
Choose Configuration Menu >
Communications Menu > Primary
Network or Advanced Network or Radio.
Note: If you are using the WTP
network, you do not need to configure
the Advanced Network parameters.
network, you do not need to configure
the Advanced Network parameters.
2
Set these parameters on the Primary Network
screen:
screen:
•
Make sure that 2.4 GHz (OpenAir radio)
or 802.11 DS (802.11b radio) appears in
the Activate field.
or 802.11 DS (802.11b radio) appears in
the Activate field.
•
For UDP Plus, set Controller IP
Address, or for TCP/IP, set Host IP
Address.
Address, or for TCP/IP, set Host IP
Address.
•
For a non-DHCP environment only, set
Terminal IP Address.
Terminal IP Address.
3
For a UDP Plus or TCP/IP network, set the
parameters on the Advanced Network screen:
parameters on the Advanced Network screen:
•
Set Network Port.
•
For the Intermec Gateway, DCS 30X,
or host on a different subnetwork, set
Default Router and Subnet Mask.
or host on a different subnetwork, set
Default Router and Subnet Mask.
4
Set these parameters on the Radio screen:
•
For a WLI Forum OpenAir radio, set
Domain and Security ID.
Domain and Security ID.
•
For an IEEE 802.11b radio and no
802.1x security, set Network Name.
Scroll to the WEP security screen and
set WEP Encryption, WEP Transmit
Key, and at least one WEP Key.
802.1x security, set Network Name.
Scroll to the WEP security screen and
set WEP Encryption, WEP Transmit
Key, and at least one WEP Key.
6
7