Intermec 2400 Quick Setup Guide
9
8
3
Place the battery pack into the upper (larger)
half of the battery compartment.
half of the battery compartment.
4
Hook the slots on the bottom of the battery
pack into the slots in the battery
compartment.
pack into the slots in the battery
compartment.
5
Slide the battery pack toward the top of the
terminal until it locks into the connectors
inside the bottom case. The battery pack
must be all the way forward to close the
battery door.
terminal until it locks into the connectors
inside the bottom case. The battery pack
must be all the way forward to close the
battery door.
6
Hook the bottom edge of the battery door
into the bottom case above the backup
battery compartment. Push the door down to
close it over the battery compartment. Slide
the battery door latch toward the top of the
terminal.
into the bottom case above the backup
battery compartment. Push the door down to
close it over the battery compartment. Slide
the battery door latch toward the top of the
terminal.
If the battery door will not shut, the battery
pack is not installed correctly. Remove the
battery pack and repeat Steps 2 through 6 to
install the battery pack.
pack is not installed correctly. Remove the
battery pack and repeat Steps 2 through 6 to
install the battery pack.
Charge the Backup Battery
Before you use the terminal for the first time,
you must fully charge the backup battery.
During normal use, the main battery pack
charges the backup battery with the terminal
turned on or off.
you must fully charge the backup battery.
During normal use, the main battery pack
charges the backup battery with the terminal
turned on or off.
To charge the backup battery
1
Install a fully charged main battery pack.
2
Leave the terminal turned off and let the
main battery pack charge the backup battery.
The backup battery will be fully charged in
about 18 hours. The main battery pack still
has most of its power remaining.
main battery pack charge the backup battery.
The backup battery will be fully charged in
about 18 hours. The main battery pack still
has most of its power remaining.
Note: The backup battery charges
enough to operate the terminal within
20 minutes. However, the backup
battery will only provide limited
backup power.
enough to operate the terminal within
20 minutes. However, the backup
battery will only provide limited
backup power.
Set the Time and Date
You can use the keypad to access the TRAKKER
Antares 2400 Menu System and set the time and
date. For help with the keypad, see “Using the
Keypad” on page 12.
Antares 2400 Menu System and set the time and
date. For help with the keypad, see “Using the
Keypad” on page 12.
To set the time and date
1
Press the q key on the top left of the
keypad. The Boot Menu appears.
keypad. The Boot Menu appears.
2
Press B to boot the terminal and initialize
the firmware.
the firmware.
•
On a 242X with the programmable
option, the sample application screen
appears.
option, the sample application screen
appears.
•
On a 2425 loaded with a TE 2000
application, the 2425 tries to connect
to the Intermec Gateway, DCS 30X,
or host. It cannot connect until you
configure the radio and network
parameters.
application, the 2425 tries to connect
to the Intermec Gateway, DCS 30X,
or host. It cannot connect until you
configure the radio and network
parameters.
3
Press ) y 2 4 8 to access the
TRAKKER Antares 2400 Menu System. The
Main Menu appears.
TRAKKER Antares 2400 Menu System. The
Main Menu appears.
4
Press { { ; to choose the System Menu,
and then press { { ;to choose the Set
Time and Date command.
and then press { { ;to choose the Set
Time and Date command.
5
Type the current time in the format
HH:MM:SS (hours:minutes:seconds) and
press {.
HH:MM:SS (hours:minutes:seconds) and
press {.
242GSG.003
Connector
end
end
Connector pin
(2 places)
(2 places)
Slots
4
5