Panasonic PT-44LCX65 User Guide
25
Basic Operation
For your convenience, First Time Set up menu will
be displayed on screen when the set is turned on
for the first time. If needed, follow the menus and
procedures displayed on-screen for setting up the
features.
be displayed on screen when the set is turned on
for the first time. If needed, follow the menus and
procedures displayed on-screen for setting up the
features.
Auto program
You can scan All (Analog and Digital) channels. If
needed, follow the menus and procedures displayed
on-screen for setting up the features. You can also make
the settings in Setup menu.
needed, follow the menus and procedures displayed
on-screen for setting up the features. You can also make
the settings in Setup menu.
Notes:
• After “Auto program” is completed the unit tunes to the first
channel found during “Auto program”.
• If setup is incomplete, check connection of Antenna/Cable to
the RF IN Terminal, then try “Auto program” again. (p. 29).
• “Auto program” must be done when you select the input
signal for the first time or whenever you change the antenna
configuration.
configuration.
• Depending on conditions, “Auto program” may take a while.
First Time Setup
Language
The language of the on-screen display is set to English
as the factory setting.
You can select English, Spanish or French as the
on-screen displays language.
as the factory setting.
You can select English, Spanish or French as the
on-screen displays language.
Press to select “Language”.
F i r s t t i m e s e t u p
L a n g u a g e
A u t o p r o g r a m
A u t o p r o g r a m
L a n g u a g e
L a n g u a g e
L a n g u a g e
◄ E n g l i s h ►
Press to display Language
screen.
screen.
1
CH
CH
VOL
VOL
OK
CH
CH
VOL
VOL
OK
Press to select “English,”
“Español” or “Français”.
“Español” or “Français”.
2
3
Press to go to previous screen.
Or, select icon, then press
OK for same results.
Or, select icon, then press
OK for same results.
A u t o p r o g r a m
A N T I n
A N T I n
◄ C a b l e ►
M o d e A l l
S t a r t s c a n
S t a r t s c a n
Press to select “ANT In”.
Press to select “Cable” or
“Antenna”.
“Antenna”.
2
CH
CH
VOL
VOL
OK
Press to select Mode.
Press to select “All” or
“Analog”.
“Analog”.
3
A u t o p r o g r a m
A N T I n C a b l e
M o d e
◄ A l l ►
S t a r t s c a n
CH
CH
VOL
VOL
OK
CH
CH
VOL
VOL
OK
4
Press to select “Start scan”.
Press to start.
Channels available for
reception will be set
automatically.
Channels available for
reception will be set
automatically.
A u t o p r o g r a m
A N T I n C a b l e
M o d e A l l
M o d e A l l
S t a r t s c a n
Now scanning analog channel ...
Progress
5
RETURN
After Auto Program is complete, the unit will return
to Manual Program mode. To place the channels
that were located by auto scan in memory, move the
cursor to “Apply” and press OK. (pp. 30-31).
If OK is not pressed after selecting OK, the channels
will not be memorized.
to Manual Program mode. To place the channels
that were located by auto scan in memory, move the
cursor to “Apply” and press OK. (pp. 30-31).
If OK is not pressed after selecting OK, the channels
will not be memorized.
F i r s t t i m e s e t u p
L a n g u a g e
A u t o p r o g r a m
A u t o p r o g r a m
Press to select “Auto program”.
Press to display Auto program
screen.
screen.
1
CH
CH
VOL
VOL
OK