Xerox M24 Supplementary Manual
5e1 - Microsoft (NetBIOS over IP) Networks
Step 5 ...continued
Microsoft (NetBIOS over IP) Networks
Before You Start
1.
Print a Settings List as stated under the Network Connectivity Tab of this guide.
2.
Referring to the Settings List, verify that "SMB" is enabled. To enable "SMB" at the Printer, if
required, follow the procedure below.
required, follow the procedure below.
3.
Referring to the Settings List, verify that DNS (or WINS, if using only a Windows NT network) is
enabled. The use of Naming Servers is REQUIRED to resolve NetBIOS device names to IP addresses
for packet routing over the TCP/IP network.
enabled. The use of Naming Servers is REQUIRED to resolve NetBIOS device names to IP addresses
for packet routing over the TCP/IP network.
4.
To enable the Printer to communicate with the Naming Servers, refer to the instructions supplied under
the selection "TCP/IP Dynamic Addressing", located in the NOS Selection menu, under the Network
Connectivity Tab of this guide.
the selection "TCP/IP Dynamic Addressing", located in the NOS Selection menu, under the Network
Connectivity Tab of this guide.
5.
When using WINS or DNS, be sure to refer to the Server Operating System documentation for the
appropriate procedure to use to enable NetBIOS name to IP address resolution on the Server.
appropriate procedure to use to enable NetBIOS name to IP address resolution on the Server.
Enabling the SMB Setting at the Printer, if required
1.
Press the rectangular Access button on the Printer Control Panel, located directly above and slightly to
the right of the numeric keypad.
the right of the numeric keypad.
2.
Press the "1" key on the numeric keypad five consecutive times. (This is the factory default
"password.")
"password.")
3.
Press the rectangular Confirm button on the touch screen.
4.
Press the System Settings button (the right-hand button of the two buttons displayed on the touch
screen). Note: If you press the left button by mistake, the Main menu will be displayed and you will have
to start over at step one above.
screen). Note: If you press the left button by mistake, the Main menu will be displayed and you will have
to start over at step one above.
5.
Press the System Settings button (the top left button displayed on screen).
6.
Press the Network Settings button (the top right button displayed on screen).
7.
Press the Port Settings button (the left-hand button) to access the Port Settings Menu display. Note: If
you press the right-hand button by mistake, you will be in the Protocol Settings Menu and will have to
press the Close button to return to the two-button selection screen.
you press the right-hand button by mistake, you will be in the Protocol Settings Menu and will have to
press the Close button to return to the two-button selection screen.
8.
When the Port Settings menu displays, press the SMB selection line.
9.
Press the Change Settings button in the lower right corner of the Port Settings Menu screen.
10.
When the SMB Selection Menu displays, note that you have only one setting selection on a single,
numbered horizontal line. Press this selection line.
numbered horizontal line. Press this selection line.
11.
Press the Change Settings button.
12.
On the Settings screen, note which of the two square buttons is highlighted as the current setting for
SMB Enablement. The available settings are Enabled or Disabled. To enable SMB at the printer, select
the Enabled setting.
SMB Enablement. The available settings are Enabled or Disabled. To enable SMB at the printer, select
the Enabled setting.
13.
Click the Save button on the touch screen, which returns you to the SMB Selection menu. (To exit the
Settings screen, without making changes, click the Cancel button.)
Settings screen, without making changes, click the Cancel button.)
14.
Exit the SMB Selection Menu and return to the Port Settings Menu by pressing the rectangular Close
button in the upper right corner of the touch screen.
button in the upper right corner of the touch screen.
15.
Exit the Port Settings Menu by pressing the rectangular Close button in the upper right corner of the
Ports Menu screen.
Ports Menu screen.
file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/main/Install_5e1.htm (1 of 3) [9/4/03 8:32:49 AM]