Xerox M24 Supplementary Manual
file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/main/Install_5g1.htm
Step 5 ...continued
Novell NetWare 3.1x (Bindery) Networks
Enable the NetWare Port at the Printer
1.
Press the rectangular Access button on the Printer Control Panel, located directly above and slightly to
the right of the numeric keypad.
the right of the numeric keypad.
2.
Press the "1" key on the numeric keypad five consecutive times. (This is the factory default
"password.")
"password.")
3.
Press the rectangular Confirm button on the touch screen.
4.
Press the System Settings button (the right-hand button of the two buttons displayed on the touch
screen). Note: If you press the left button by mistake, the Main menu will be displayed and you will have
to start over at step one above.
screen). Note: If you press the left button by mistake, the Main menu will be displayed and you will have
to start over at step one above.
5.
Press the System Settings button (the top left button displayed on screen).
6.
Press the Network Settings button (the top right button displayed on screen).
7.
Press the Port Settings button (the left-hand button) to access the Port Settings Menu. Note: If you
press the right-hand button by mistake, you will be in the Protocol Settings Menu and will have to press
the Close button to return to the two-button selection screen.
press the right-hand button by mistake, you will be in the Protocol Settings Menu and will have to press
the Close button to return to the two-button selection screen.
8.
Press the NetWare selection line on the Port Settings Menu screen.
9.
Press the Change Settings button in the lower right corner of the Port Settings Menu screen.
10.
When the NetWare Port Selection Menu displays, note that you have only one selection on a single,
numbered horizontal line. Press this selection labeled Port Status.
numbered horizontal line. Press this selection labeled Port Status.
11.
Press the Change Settings button.
12.
On the Settings screen, note which of the two square buttons is highlighted as the current setting for
NetWare Port Enablement. The available settings are Enabled or Disabled. To enable NetWare at the
Printer, select the Enabled setting.
NetWare Port Enablement. The available settings are Enabled or Disabled. To enable NetWare at the
Printer, select the Enabled setting.
13.
Press the Save button (upper right-hand button) on the touch screen, which returns you to the NetWare
Port Selection Menu.
Port Selection Menu.
14.
Exit the NetWare Port Selection Menu and return to the Port Settings Menu by pressing the rectangular
Close button in the upper right corner of the touch screen.
Close button in the upper right corner of the touch screen.
15.
Exit the Port Settings Menu by pressing the rectangular Close button in the upper right corner of the
Port Settings Menu screen.
Port Settings Menu screen.
16.
Exit the Ports and Protocols selection screen by pressing the rectangular Close button in the upper
right corner of the screen.
right corner of the screen.
17.
Exit the screen containing the Network Settings button by pressing the rectangular Close button in the
upper right corner of the screen.
upper right corner of the screen.
18.
Finally, press the rectangular Exit button in the upper right corner of the four-button, System Settings
screen to have the printer reboot and enable your NetWare setting.
screen to have the printer reboot and enable your NetWare setting.
Set Up a Print Server, Queue, and Name on the Primary Server
1.
Set up a Print Server, Queue, and Printer Configuration on the Primary Server using PCONSOLE.
Refer to the documentation supplied by Novell (
Refer to the documentation supplied by Novell (
) to complete this task.
Note: Record precisely (observe upper and lower case, punctuation etc.) the following: the Primary
Server name, Frame type used, Print Server name, Print Server password, and the Queue name
assigned. If your printer services queues on multiple fileservers, the Print Server name must be the
Server name, Frame type used, Print Server name, Print Server password, and the Queue name
assigned. If your printer services queues on multiple fileservers, the Print Server name must be the
file:///C|/0-web/boxster/WorkCentreM24-System-Analyst-Guide/main/Install_5g1.htm (1 of 3) [9/4/03 8:32:50 AM]