D-Link DMI-128ESU User Manual
D-LINK ISDN TA DMI-128ESU+
32
AT&F
Recall factory default setting
The factory configuration contained in the
ROM is loaded to become the TA’s
configuration.
ROM is loaded to become the TA’s
configuration.
AT&Kn
Flow control
0
*3
4
4
• No flow control
• Hardware flow control (RTS/CTS)
• Software flow control (Xon/Xoff)
AT&Sn
DR signal control
Defines how the DSR (DR) signal is
handled by the TA
Defines how the DSR (DR) signal is
handled by the TA
*0
1
1
• TA‘s DSR (DR) signal follows DTE’s
DTR
DTR
• DSR (DR) signal on at only
communication time.
(DSR signal high during
communication time)
communication time)
AT&Vn
Display system configuration
Cause the TA to display its current
configuration
Cause the TA to display its current
configuration
0
2
2
• Displays the current
configuration
• Display Directory Numbers and all
stored phone numbers
stored phone numbers
AT&Wn
Write user profile
The TA ‘s active configuration will
be stored into the non-volatile
memory as User profile
be stored into the non-volatile
memory as User profile
0
1
1
• Write user profile 0
• Write user profile 1
AT&Yn
Load user configuration when power on
0
1
1
• Use user profile 0 as active Profile
when power up
• Use user profile 1 as active Profile
when power up
AT&Zn=x
Register speed dial number
n
x
x
• n = 0-19
• x = telephone number
AT%A2=n
Data port protocol selection
Select the protocol on BOD channel
Select the protocol on BOD channel
1
2
4
2
4
*5
6
8
8
14
• V.110
• V.120
• X.25 on D
• PPP
• MLPPP
• X.75
• Channel Bundling
AT%A5=n
Enbloc/overlap sending mode
Select the sending method for telephone
number (refer also AY*W0, AT*W1)
Select the sending method for telephone
number (refer also AY*W0, AT*W1)
*0
1
• Overlap sending
The dialing telephone will be sent to
network after TA detect the ending digit
network after TA detect the ending digit
• Enbloc sending
The dialing telephone number will be
sent to network immediately whenever
the user dialing each digit
sent to network immediately whenever
the user dialing each digit
AT%D
Data port setting display
Display all corresponding setting
AT%DC
Show disconnect cause, source, charge
Display the disconnect reason and
connection fee
connection fee
AT%FAPPS
Re-Flash the new software
AT%N=x
Set data port directory number / sub-
address
(eg. AT%N=12345678 + 12345)
address
(eg. AT%N=12345678 + 12345)
x
• x=telephone number
main - address: max 20 digits
sub - address: max 5 digits
main - address: max 20 digits
sub - address: max 5 digits
AT%Sn
Data port call screen function enable
0
*1
• Accept incoming call if the calling
party number is in the call screen table.
party number is in the call screen table.
• Accept all incoming call
AT%Z1
Software reset
Reset all internal state of TA
AT$AAn
Set analog port A voice information
capability in answer mode
capability in answer mode
0
1
1
*2
• Accept speech
• Accept 3.1kHz audio
• Accept both
AT$AN=x
Set analog port A directory number / sub-
address (Not used in Finland)
Eg. AT$AN1234567812345
address (Not used in Finland)
Eg. AT$AN1234567812345
x
• X = telephone number
Main - address: max 20 digits
Sub - address: max 5 digits