KitchenAid 30" Single Wall Oven with Even-Heat™ Thermal Bake/Broil Dimensional Illustrations

27" (68.6 CM) AND 30" (76.2 CM) ELECTRIC SINGLE AND DOUBLE BUILT-IN OVEN

PRODUCT MODEL NUMBERS

KODE300E

KODE307E

KODE500E

KODE507E

PRODUCT DIMENSIONS

27" (68.6 cm) models

A. 28¾" (72.8 cm) max. overall

height

B. 257⁄16" (64.6 cm) max. recessed

width

C. 26³⁄4" (67.9 cm) recessed

height

D. 23¹⁄4" (59.1 cm) max. recessed

depth

E. 27" (68.6 cm) overall width

F. 12" (30.5 cm) from back of

control panel to start of strain

relief

G. 48" (121.9 cm) flexible conduit

length

Page 1 of 2

KODT100E

KODT107E

KOSE500E

KOSE507E

KOST100E

KOST107E

KEBS109E

KEBS209E

KEBS207E

Electrical: To properly install your oven, you must determine the type

of electrical connection you will be using and follow the instructions

provided for it here.

•

Oven must be connected to the proper electrical voltage and

frequency as specified on the model/serial number rating plate.

The model/serial number rating plate is located under the control

panel on single ovens and under the control panel on the upper

oven cavity on double ovens. See the following illustrations.

art

Single Oven

Double Oven

A. Model/serial number plate

•

Models rated from 7.3 to 9.6 kW at 240 volts (5.4 to 7.4 kW at 208

volts) require a separate 40-amp circuit. Models rated at 4.8 kW

and below at 240 volts (3.6 kW and below at 208 volts) require a

separate 20-amp circuit.

•

A circuit breaker is recommended.

•

Connect directly to the circuit breaker box (or fused disconnect)

through flexible, armored or nonmetallic sheathed, copper cable

(with grounding wire). See “Make Electrical Connection” section.

•

Flexible conduit from the oven should be connected directly to the

junction box.

•

Fuse both sides of the line.

•

Do not cut the conduit. The length of conduit provided is for

serviceability of the oven.

•

A UL listed or CSA approved conduit connector must be provided.

•

If the house has aluminum wiring, follow the procedure below:

1. Connect a section of solid copper wire to the ends of the

flexible conduit leads.

2. Connect the aluminum wiring to the added section of copper

wire using special connectors and/or tools designed and UL

listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with local

codes and industry accepted wiring practices.
For power requirements for models KOST107E, KOST100E,

KOSE507E, KOSE500E, KODE307E, KODE300E, KODE507E,

KODE500E, KODT100E and KODT107E, refer to the following table.

Voltage

Single

Thermal

Single

Convect

Double

Thermal

Double

Convect

Double

Convect/

Thermal

240 VAC

4100 W

8163 W

8300 W

208 VAC

3100 W

6300 W

240 VAC

17.2 A

34.2 A

208 VAC

15.0 A

29.9 A

30" (76.2 cm) models

A. 28¾" (72.8 cm) max. overall

height

B. 28½" (72.4 cm) max. recessed

width

C. 26³⁄4" (67.9 cm) recessed height

D. 23¹⁄4" (59.1 cm) max. recessed

depth

E. 30" (76.2 cm) overall width

F. 12" (30.5 cm) from back of

control panel to start of strain

relief

G. 48" (121.9 cm) flexible conduit

length

art

27" (68.6 cm) models

A. 51³⁄16" (130.0 cm)

max. overall height

B. 257⁄16" (64.6 cm)

max. recessed width

C. 48¹³⁄16" (124.0 cm)

recessed height

D. 23¹⁄4" (59.1 cm)

max. recessed depth

E. 27" (68.6 cm) overall width

F. 12" (30.5 cm) from back

of control panel to start

of strain relief

G. 66" (167.6 cm) flexible

conduit length

30" (76.2 cm) models

A. 51³⁄16" (130.0 cm)

max. overall height

B. 28½" (72.4 cm)

max. recessed width

C. 48¹³⁄16" (124.0 cm)

recessed height

D. 23¹⁄4" (59.1 cm)

max. recessed depth

E. 30" (76.2 cm) overall width

F. 12" (30.5 cm) from back

of control panel to start

of strain relief

G. 66" (167.6 cm) flexible

conduit length

Ref. W10725670B

05/15