Craftsman 54990 User Manual
Install The Protector System
®
(Continued)
INSTALLING THE BRACKETS
Be sure power to the opener is disconnected. Install and align
the brackets so the sensors will face each other across the garage
door, with the beam no higher than 6" (15 cm) above the floor.
They may be installed in one of three ways, as follows.
Be sure power to the opener is disconnected. Install and align
the brackets so the sensors will face each other across the garage
door, with the beam no higher than 6" (15 cm) above the floor.
They may be installed in one of three ways, as follows.
Garage door track installation (preferred):
1. Slip the curved arms over the rounded edge of each door
1. Slip the curved arms over the rounded edge of each door
track, with the curved arms facing the door. Snap into place
against the side of the track. It should lie flush, with the lip
hugging the back edge of the track, as shown in Figure 1.
against the side of the track. It should lie flush, with the lip
hugging the back edge of the track, as shown in Figure 1.
If your door track will not support the bracket securely, wall
installation is recommended.
installation is recommended.
Wall installation (Figures 2 & 3):
1. Place the bracket against the wall with curved arms facing the
1. Place the bracket against the wall with curved arms facing the
door. Be sure there is enough clearance for the sensor beam to
be unobstructed.
2. If additional depth is needed, an extension bracket (see
Accessories) or wood blocks can be used.
3. Use bracket mounting holes as a template to locate and drill
(2) 3/16" diameter pilot holes on the wall at each side of the
door, no higher than 6" (15 cm) above the floor.
door, no higher than 6" (15 cm) above the floor.
4. Attach brackets to wall with lag screws (not provided).
5. If using extension brackets or wood blocks, adjust right and
5. If using extension brackets or wood blocks, adjust right and
left assemblies to the same distance out from the mounting
surface. Make sure all door hardware obstructions are cleared.
surface. Make sure all door hardware obstructions are cleared.
Floor installation (Figure 4):
1. Use wood blocks or extension brackets (see Accessories) to
1. Use wood blocks or extension brackets (see Accessories) to
elevate sensor brackets so the lenses will be no higher than
6" (15 cm) above the floor.
6" (15 cm) above the floor.
2. Carefully measure and place right and left assemblies at the
same distance out from the wall. Be sure all door hardware
obstructions are cleared.
obstructions are cleared.
3. Fasten to the floor with concrete anchors as shown.
Wing Nut
1/4"-20
1/4"-20
Insulated Staples
(Not Shown)
Carriage Bolt
1/4"-20x1/2"
1/4"-20x1/2"
HARDWARE SHOWN ACTUAL SIZE
Indicator
Light
Light
Lens
Lip
Door
Track
Track
Indicator
Light
Light
Lens
Extension Bracket
(See Accessories)
(See Accessories)
Inside
Garage
Wall
Garage
Wall
(Provided with
Extension Bracket)
Extension Bracket)
(Provided with
Extension Bracket)
Extension Bracket)
Attach with
Concrete Anchors
(Not provided)
Concrete Anchors
(Not provided)
Inside
Garage
Wall
Lens
Indicator
Light
Light
Inside
Garage
Wall
Garage
Wall
Indicator
Light
Light
Safety
Reversing
Sensor
Bracket
Reversing
Sensor
Bracket
Safety
Reversing
Sensor
Bracket
Reversing
Sensor
Bracket
Lens
Lag Screws
(Not provided)
(Not provided)
Fasten Wood Block to Wall with
Lag Screws (Not provided)
Lag Screws (Not provided)
Safety
Reversing
Sensor
Bracket
Reversing
Sensor
Bracket
Safety
Reversing
Sensor
Bracket
Reversing
Sensor
Bracket
Figure 1
DOOR TRACK MOUNT (RIGHT SIDE)
WALL MOUNT (RIGHT SIDE)
WALL MOUNT (RIGHT SIDE)
FLOOR MOUNT (RIGHT SIDE)
Figure 2
Figure 3
Figure 4
24