Fujifilm Transfers Leaflet
Texopaque Hot Peel Transfer System
Product Information
SERICOL
Texopaque Classic OP and Advantage ON are plastisol inks that can
be used for direct printing, or as part of a Hot Peel transfer system
as detailed below.
be used for direct printing, or as part of a Hot Peel transfer system
as detailed below.
These inks can be selected depending on the requirement to
comply to legislation on phthalate content.
comply to legislation on phthalate content.
Texopaque Advantage ON inks are formulated to be compliant
(1).
Hot Peel Method
Use Texopaque Classic OP or Texopaque Advantage ON ink as
appropriate with a 3-5 % addition of ON417 Special Expanding Base.
appropriate with a 3-5 % addition of ON417 Special Expanding Base.
Mesh Count 21-62 (or up to 120 if a back-up white or adhesive is used).
Drying Heat set on paper until touch dry.
Typically 110-120° C for 15-30 seconds dependent on the heat source.
Typically 110-120° C for 15-30 seconds dependent on the heat source.
Thinning If required, up to 5% ZE591Plastisol Flow Thinner, or ON591
Advantage Flow Thinner where Phthalate compliant required.
Advantage Flow Thinner where Phthalate compliant required.
Recommended paper TRH01 transfer paper.
Recommended Transfer Schedule
185-190° C, 10-15 seconds, high pressure,
When using an adhesive, 160-180° C is recommended
185-190° C, 10-15 seconds, high pressure,
When using an adhesive, 160-180° C is recommended
IMPORTANT: PEEL PAPER WHILE TRANSFER IS HOT.
Note: when producing Advantage ON Phthalate compliant
transfers, ensure the correct adhesive and thinner is selected to
maintain phthalate compliance.
transfers, ensure the correct adhesive and thinner is selected to
maintain phthalate compliance.
Adhesive
XM452 Adhesive can be used to overprint Texopaque Classic OP
Colours. TJ451 and TJ452 adhesives can be used to over print
Texopaque Advantage ON colours to give better adhesion to synthetic
substrates, or to reduce the transfer temperature to 160-180 ° C
Colours. TJ451 and TJ452 adhesives can be used to over print
Texopaque Advantage ON colours to give better adhesion to synthetic
substrates, or to reduce the transfer temperature to 160-180 ° C
Maximum adhesion onto synthetic garments can be achieved using
the XM378 Transfer Adhesive Powder. To use this process, print the
plastisol ink as recommended, sprinkle the back of the wet ink with the
adhesive powder prior to setting. Vacuum/shake to remove excess.
the XM378 Transfer Adhesive Powder. To use this process, print the
plastisol ink as recommended, sprinkle the back of the wet ink with the
adhesive powder prior to setting. Vacuum/shake to remove excess.
Due to the variable nature of synthetic coatings, prints should be fully
tested for suitability before commencing production.
tested for suitability before commencing production.
Recommended Transfer Equipment
Flat-bed Transfer Press
It is important to avoid over cure, especially with multicolour
transfers, as adhesion and transfer properties can be affected.
transfers, as adhesion and transfer properties can be affected.
Paper
The Hot Peel system will only work with TRH01 Hot Peel Paper.
For other types of transfers please select the appropriate paper.
For other types of transfers please select the appropriate paper.
Colour Range
Classic OP
OP001
OP001
Black
OP021
White
OP025
Super Opaque White
OP042 (S)
Seritone Yellow (Green Shade)/Mid Chrome
OP043 (S)
Seritone Yellow (Red Shade)/Mid Chrome
OP045
Yellow
OP101
Light Orange
OP162 (S)
Seritone Orange/Light Red
OP165 (S)
Seritone Magenta
OP166 (S)
Seritone Violet
OP199
Warm Red
OP134 (S)
Seritone Red (Yellow Shade)/Red
OP124 (S)
Seritone Red (Blue Shade)/Deep Red
OP227
Light Blue
OP212
Blue
OP207
Navy Blue
OP203 (S)
Seritone Blue /Mid Blue
OP206 (S)
Seritone Blue (RS) /Deep Blue
OP283
Bright Green
OP285 (S)
Seritone Green /Deep Green
OP320
Green
OP381
Extender Base
Available in both 1ltr & 5ltr containers
Advantage ON - Phthalate compliant
(1)
ON001
Black
ON021
White
ON042 (S)
Seritone Yellow (Green Shade)/Light Chrome
ON043 (S)
Seritone Yellow (Red Shade)/Mid Chrome
ON162 (S)
Seritone Yellow Orange/Light Red
ON165 (S)
Seritone Magenta
ON166 (S)
Seritone Violet
ON134 (S)
Seritone Red (Yellow Shade)/Red
ON124 (S)
Seritone Red (Blue Shade)/Deep Red
ON203 (S)
Seritone Blue/Mid Blue
ON206 (S)
Seritone Blue (Red Shade)/Deep Blue
ON210
Ultra Blue
ON285 (S)
Seritone Green/Deep Green
ON077
Fluorescent Yellow
ON119
Fluorescent Orange
ON179
Fluorescent Red
ON180
Fluorescent Magenta
ON294
Fluorescent Green
ON417
Special Expanding Base
ON381
Extender Base
Available in 5ltr containers
(S) = Seritone Base Colour
SERICOL