Bosch GLL 2-80 P 0601063200 User Manual
Product codes
0601063200
English | 21
Bosch Power Tools
1 609 929 S04 | (30.6.09)
Checking the Levelling Accuracy of the
Vertical Line
For this check, a door opening is required with
at least 2.5 metres of space (on a firm surface)
to each side of the door.
– Position the measuring tool on a firm, level
Vertical Line
For this check, a door opening is required with
at least 2.5 metres of space (on a firm surface)
to each side of the door.
– Position the measuring tool on a firm, level
surface (not on a tripod) 2.5 m away from
the door opening. Allow the measuring tool
to level in while in vertical operation with au-
tomatic levelling, and direct the laser beam
at the door opening.
the door opening. Allow the measuring tool
to level in while in vertical operation with au-
tomatic levelling, and direct the laser beam
at the door opening.
– Mark the centre of the vertical laser line at
the floor of the door opening (point I), at a
distance of 5 metres beyond the other side of
the door opening (point II) and at the upper
edge of the door opening (point III).
distance of 5 metres beyond the other side of
the door opening (point II) and at the upper
edge of the door opening (point III).
– Rotate the measuring tool by 180° and posi-
tion it on the other side of the door opening
directly behind point II. Allow the measuring
directly behind point II. Allow the measuring
tool to level in and align the vertical laser line
in such a manner that its centre runs exactly
through points I and II.
in such a manner that its centre runs exactly
through points I and II.
– Mark the centre of the laser line at the upper
edge of the door opening as point IV.
– The difference d of both marked points III
and IV results in the actual deviation of the
measuring tool to the plumb line.
measuring tool to the plumb line.
– Measure the height of the door opening.
The maximum admissible deviation is calculated
as follows:
Doubled height of the door opening x 0.2 mm/m
Example: For a door-opening height of 2 m, the
maximum deviation may be
2 x 2 m x ±0.2 mm/m = ±0.8 mm. Consequently,
points III and IV may be no more than 0.8 mm
(max.) apart from each other.
The maximum admissible deviation is calculated
as follows:
Doubled height of the door opening x 0.2 mm/m
Example: For a door-opening height of 2 m, the
maximum deviation may be
2 x 2 m x ±0.2 mm/m = ±0.8 mm. Consequently,
points III and IV may be no more than 0.8 mm
(max.) apart from each other.
Working Advice
f
Always use the centre of the laser line for
marking. The width of the laser line changes
with the distance.
marking. The width of the laser line changes
with the distance.
Working with the laser target plate
The laser target plate 15 increases the visibility
of the laser beam under unfavourable condi-
tions and at large distances.
The reflective part of the laser target plate 15
improves the visibility of the laser line. Thanks
to the transparent part, the laser line is also vis-
ible from the back side of the laser target plate.
The laser target plate 15 increases the visibility
of the laser beam under unfavourable condi-
tions and at large distances.
The reflective part of the laser target plate 15
improves the visibility of the laser line. Thanks
to the transparent part, the laser line is also vis-
ible from the back side of the laser target plate.
Working with the Tripod (Accessory)
A tripod offers a stable, height-adjustable meas-
uring support. Position the measuring tool with
the 1/4" tripod mount 10 onto the thread of the
tripod 21 or a commercially available camera tri-
pod. For fastening to a commercially available
construction tripod, use the 5/8" tripod mount
9. Tighten the measuring tool with the tripod
mounting stud.
A tripod offers a stable, height-adjustable meas-
uring support. Position the measuring tool with
the 1/4" tripod mount 10 onto the thread of the
tripod 21 or a commercially available camera tri-
pod. For fastening to a commercially available
construction tripod, use the 5/8" tripod mount
9. Tighten the measuring tool with the tripod
mounting stud.
Fastening with the Universal Holder
(Accessory) (see figure D)
With the universal holder 19, you can fasten the
measuring tool, e.g., to vertical surfaces, pipes
or magnetizable materials. The universal holder
is also suitable for use as a ground tripod and
makes the height adjustment of the measuring
tool easier.
(Accessory) (see figure D)
With the universal holder 19, you can fasten the
measuring tool, e.g., to vertical surfaces, pipes
or magnetizable materials. The universal holder
is also suitable for use as a ground tripod and
makes the height adjustment of the measuring
tool easier.
2,5 m
2,5 m
2 m
d
OBJ_BUCH-907-001.book Page 21 Tuesday, June 30, 2009 2:32 PM