Intel Celeron 440 HH80557RG041512 Data Sheet
Product codes
HH80557RG041512
Datasheet
19
Electrical Specifications
2.6.2
DC Voltage and Current Specification
NOTES:
1.
1.
Unless otherwise noted, all specification in this table are based on estimates and
simulation or empirical data. These specifications will be updated with characterized data
from silicon measurements at a later date.
simulation or empirical data. These specifications will be updated with characterized data
from silicon measurements at a later date.
2.
Adherence to the voltage specification for the processor are required to ensure reliable
processor operation.
processor operation.
3.
Each processor is programmed with a maximum valid voltage identification value (VID),
which is set at manufacturing and can not be altered. Individual maximum VID values are
calibrated during manufacturing such that two processors at the same frequency may have
different settings within the VID range. Please note this differs from the VID employed by
the processor during a power management event (Thermal Monitor 2).
which is set at manufacturing and can not be altered. Individual maximum VID values are
calibrated during manufacturing such that two processors at the same frequency may have
different settings within the VID range. Please note this differs from the VID employed by
the processor during a power management event (Thermal Monitor 2).
4.
These voltages are targets only. A variable voltage source should exist on systems in the
event that a different voltage is required. See
event that a different voltage is required. See
and
for more
information.
5.
The voltage specification requirements are measured across VCC_SENSE and VSS_SENSE
lands at the socket with a 100 MHz bandwidth oscilloscope, 1.5 pF maximum probe
capacitance, and 1 MΩ minimum impedance. The maximum length of ground wire on the
probe should be less than 5 mm. Ensure external noise from the system is not coupled into
the oscilloscope probe.
lands at the socket with a 100 MHz bandwidth oscilloscope, 1.5 pF maximum probe
capacitance, and 1 MΩ minimum impedance. The maximum length of ground wire on the
probe should be less than 5 mm. Ensure external noise from the system is not coupled into
the oscilloscope probe.
6.
Refer to
for the minimum, typical, and maximum V
CC
allowed for a
given current. The processor should not be subjected to any V
CC
and I
CC
combination
wherein V
CC
exceeds V
CC_MAX
for a given current.
7.
I
CC_MAX
specification is based on the V
CC_MAX
loadline. Refer to
f or details.
Table 5.
Voltage and Current Specifications
Symbol
Parameter
Min
Typ
Max
Unit
Notes
2, 15
VID Range
VID
1.0000
—
1.3375
V
3
V
CC
Processor Number
450
440
430
420
440
430
420
Core V
CC
2.2 GHz
2.0 GHz
1.8 GHz
1.6 GHz
2.0 GHz
1.8 GHz
1.6 GHz
Refer to
V
4, 5, 6
V
CC_BOOT
Default V
CC
voltage for initial power up
—
1.10
—
V
V
CCPLL
PLL V
CC
- 5%
1.50
+ 5%
I
CC
Processor Number
450
440
430
420
440
430
420
I
CC
for
775_VR_CONFIG_06
2.2 GHz
2.0 GHz
1.8 GHz
1.6 GHz
2.0 GHz
1.8 GHz
1.6 GHz
—
—
35
35
35
35
35
35
35
A
7
V
TT
FSB termination voltage
(DC + AC specifications)
(DC + AC specifications)
1.14
1.20
1.26
V
8
VTT_OUT_LEFT
and
VTT_OUT_RIGHT
I
and
VTT_OUT_RIGHT
I
CC
DC Current that may be drawn from
VTT_OUT_LEFT and VTT_OUT_RIGHT per pin
VTT_OUT_LEFT and VTT_OUT_RIGHT per pin
—
—
580
mA
9
I
TT
I
CC
for V
TT
supply before V
CC
stable
I
CC
for V
TT
supply after V
CC
stable
—
—
4.5
4.6
4.6
A
10
I
CC_VCCPLL
I
CC
for PLL land
—
—
130
mA
I
CC_GTLREF
I
CC
for GTLREF
—
—
200
μA