Cisco Cisco ASA 5580 Adaptive Security Appliance Leaflet
7-39
思科 ASA 系列命令参考,S 命令
第 7 章 show failover 至 show ipsec stats traffic 命令
show interface
使用指南
如果在各情景之间共享接口,并且您在情景内输入此命令,则
ASA 仅显示当前情景中的统计信
息。当您在系统执行空间中对物理接口输入此命令时,
ASA 显示所有情景的合并统计信息。
为子接口显示的统计信息数量是为物理接口显示的统计信息数量的子集。
不能在系统执行空间中使用接口名称,因为
nameif 命令只能用于情景中。同样,如果使用
allocate-interface
命令将接口 ID 映射到某个映射名称,则只能在情景中使用该映射名称。如果您在
allocate-interface 命令中设置
visible 关键字,则 ASA 在 show interface 命令输出中显示接口 ID。
注意
硬件中传输或接收的字节数计数和流量统计信息计数不同。
在硬件计数中,数量直接从硬件检索,并反映第
2 层数据包大小。而在流量统计信息中,它反映
第
3 层数据包大小。
计数差异因接口卡硬件的具体设计而有所不同。
例如,对于快速以太网卡,因为它包括以太网标头,所以第
2 层计数比流量计数大 14 字节。对于
千兆以太网卡,因为它包括以太网标头和
CRC,所以第 2 层计数比流量计数大 18 字节。
请参阅 “ 示例 ” 部分,了解显示输出的说明。
示例
以下是
show interface 命令的输出示例:
ciscoasa# show interface
Interface GigabitEthernet0/0 "outside", is up, line protocol is up
Hardware is i82546GB rev03, BW 1000 Mbps, DLY 1000 usec
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
MAC address 000b.fcf8.c44e, MTU 1500
IP address 10.86.194.60, subnet mask 255.255.254.0
1328522 packets input, 124426545 bytes, 0 no buffer
Received 1215464 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
9 L2 decode drops
124606 packets output, 86803402 bytes, 0 underruns
0 output errors, 0 collisions
0 late collisions, 0 deferred
0 input reset drops, 0 output reset drops
input queue (curr/max packets): hardware (0/7)
output queue (curr/max packets): hardware (0/13)
Traffic Statistics for "outside":
1328509 packets input, 99873203 bytes
124606 packets output, 84502975 bytes
524605 packets dropped
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
8.2(1)
将无缓冲区号更改为显示块分配的失败数。
8.6(1)
此命令添加了对
ASA 5512-X 到 ASA 5555-X 共享管理接口和软件模块
的控制平面接口的支持。使用
show interface detail 命令可将管理接口
显示为
Internal-Data0/1 ;将控制平面接口显示为 Internal-Control0/0。
版本
修改