Cisco Cisco Nexus 1010 Virtual Services Appliance Troubleshooting Guide
S e n d d o c u m e n t c o m m e n t s t o n e x u s 1 k - d o c f e e d b a c k @ c i s c o . c o m .
5
Cisco Nexus Virtual Services Appliance Troubleshooting Guide, Release 4.2(1)SP1(5.1)
OL-27731-01
Cisco Nexus Virtual Services Appliance Troubleshooting Commands
Cisco Nexus Virtual Services Appliance Troubleshooting
Commands
Commands
You can use the commands in this section to troubleshoot problems related to Cisco Nexus Virtual
Services Appliance.
Services Appliance.
Any changes to network uplink type
assignment fails with the following
error message:
assignment fails with the following
error message:
Cannot assign a port or a port
channel with itself or member
port in administratively shut
state to control interface
One of the members of the port
channel is administratively down.
channel is administratively down.
1.
Verify if any of the port is in
administratively down state.
administratively down state.
show network summary
2.
Bring the port to administratively up state.
no shut
3.
Reassign network uplink type in Cisco
Nexus Virtual Services Appliance.
Nexus Virtual Services Appliance.
See the Cisco Nexus Virtual Services Appliance
Software Configuration Guide, Release
4.2(1)SP1(5.1) for assigning uplink types.
Software Configuration Guide, Release
4.2(1)SP1(5.1) for assigning uplink types.
Removal of port channel fails with
the following error message:
the following error message:
Interface (GigabitEthernet1)
pc in use by rt mgr while
trying to remove a Gig member
from a port channel.
The port channel is in use by Cisco
Nexus Virtual Services Appliance.
Nexus Virtual Services Appliance.
Verify if the port channel is in use in theCisco
Nexus Virtual Services Appliance
Nexus Virtual Services Appliance
Show network summary
Show network port-channel summary
VSB is not created on the secondary
Cisco Nexus Virtual Services
Appliance even if the Cisco Nexus
Virtual Services Appliance is in sync
and in HA mode.
Cisco Nexus Virtual Services
Appliance even if the Cisco Nexus
Virtual Services Appliance is in sync
and in HA mode.
An error occurred during the
automatic creation of the VSB on
the secondary Cisco Nexus Virtual
Services Appliance.
automatic creation of the VSB on
the secondary Cisco Nexus Virtual
Services Appliance.
Manually create the VSB on the secondary Cisco
Nexus Virtual Services Appliance.
Nexus Virtual Services Appliance.
See the Cisco Nexus Virtual Services Appliance
Software Configuration Guide, Release
4.2(1)SP1(5.1) for creating VSBs.
Software Configuration Guide, Release
4.2(1)SP1(5.1) for creating VSBs.
After rebooting the Cisco Nexus
Virtual Services Appliances, the
configured VSBs do not appear.
Virtual Services Appliances, the
configured VSBs do not appear.
Cisco Nexus Virtual Services
Appliance configuration may not
have been saved after creating the
VSBs.
Appliance configuration may not
have been saved after creating the
VSBs.
Contact a customer service representative for
assistance to recover pointers to the VSBs.
assistance to recover pointers to the VSBs.
Note
Do not attempt to modify the Cisco
Nexus Virtual Services Appliance
configuration or reload the VSB.
Nexus Virtual Services Appliance
configuration or reload the VSB.
Table 1-1
Problems with Cisco Nexus Virtual Services Appliance Product Family
Symptom
Possible Causes
Verification and Solution
Table 2
Cisco Nexus Virtual Services Appliance Troubleshooting Commands
Command
Purpose
show tech-support
Displays switch information for Cisco TAC to
assist you in diagnosing issues
assist you in diagnosing issues
show network
Displays information about the network.