Intel 530 LF80537NE0301M Data Sheet
![Intel](https://files.manualsbrain.com/attachments/5a71b1e7f60391972dadeef20435931cbf4621a5/common/fit/150/50/86c99b5f14aeb2708e9a9e1b5305af4ccf882c1af0155dad25413c2ed84e/brand_logo.png)
Product codes
LF80537NE0301M
Datasheet
29
Electrical Specifications
Table 8 lists the DC specifications for the processor and are valid only while meeting
specifications for junction temperature, clock frequency, and input voltages. The
Highest Frequency Mode (HFM) and Lowest Frequency Mode (LFM) refer to the highest
and lowest core operating frequencies supported on the Genuine Intel Processor. Unless
specified otherwise, all specifications for the processor are at Tjunction =100 ºC. Care
should be taken to read all notes associated with each parameter.
NOTES:
1.
1.
Each processor is programmed with a maximum valid voltage identification value (VID), which is set at
manufacturing and can not be altered. Individual maximum VID values are calibrated during
manufacturing such that two processors at the same frequency may have different settings within the VID
range. Note that this differs from the VID employed by the processor during a power management event
(ex: Extended Halt State).
2.
The voltage specifications are assumed to be measured across V
CCSENSE
and V
SSSENSE
pins at socket with a
100-MHz bandwidth oscilloscope, 1.5-pF maximum probe capacitance, and 1-mΩ minimum impedance.
The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from
the system is not coupled in the scope probe.
The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from
the system is not coupled in the scope probe.
3.
Specified at 100°C Tj.
4.
Specified at nominal V
CC
.
Table 8.
Voltage and Current Specifications for the Ultra Low Voltage Dual-Core 1M
Cache Intel Celeron SFF Genuine Intel Processor
Symbol
Parameter
Min
Typ
Max
Unit
Notes
V
CC
V
CC
of the Processor Core
0.8
1.1
V
1, 2
V
CC,BOOT
Default V
CC
Voltage for Initial Power Up
—
1.20
—
V
2, 8
V
CCP
AGTL+ Termination Voltage
1.00
1.05
1.10
V
V
CCA
PLL Supply Voltage
1.425
1.5
1.575
V
I
CCDES
I
CC
for Processors Recommended Design Target
—
—
18
A
5
I
CC
I
CC
for processors
A
Processor
Number
Number
Frequency
Die Variant
SU2300
1.2GHz
1MB
17.6
A
3, 4
I
AH,
I
SGNT
I
CC
Auto-Halt & Stop-Grant
—
—
6.3
A
3, 4
I
SLP
I
CC
Sleep
—
—
5.9
A
3, 4
I
DSLP
I
CC
Deep Sleep
—
—
5.0
A
3, 4
I
DPRSLP
I
CC
Deeper Sleep
—
—
3.2
A
3, 4
dI
CC/
DT
V
CC
Power Supply Current Slew Rate at
Processor Package Pin
—
—
600
A/µs
7
I
CCA
I
CC
for V
CCA
Supply
—
—
130
mA
I
CCP
I
CC
for V
CCP
Supply before V
CC
Stable
I
CC
for V
CCP
Supply after V
CC
Stable
—
—
4.5
2.5
2.5
A
A
A
8
9
9