Cisco Cisco Prisma II EDR Receiver Data Sheet
![Cisco](https://files.manualsbrain.com/attachments/7380d0050044647c30f5c24bbbf5d0c0b6d9bb84/common/fit/150/50/faa183d287233c52228cfea3dbc2a127fe780f60564fcb0955d9c3d1cd23/brand_logo.png)
© 2007-2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 4 of 8
Data Sheet
Product Specifications
Table 1.
Optical Specifications
Feature
Units
HD-RXR Standard Gain
and High Gain
and High Gain
HD-RXR Low Noise
Notes
Input Power
dBm
-17 to -8 (High Gain)
-17 to 0 (Standard Gain)
-25 to -10
Wavelength
nm
1290 to 1620
1290 to 1620
Optical Return Loss
dB
> 30
> 30
Optical Interface: SC/APC
Standard
Standard
Table 2.
Electrical Specifications
Feature
Units
HD-RXR Standard Gain
and High Gain
and High Gain
HD-RXR Low Noise
Notes
RF Bandwidth
MHz
5 to 90
5 to 90
RF Output Level
dBmV
Use RF output level
calculations (see previous
section)
Use RF output level
calculations (see previous
section)
Maximum RF Output Level
dBmV
58 (Composite)
58 (Composite)
1
RF Attenuation Range
dB
0 to 26 in 0.75 dB steps
0 to 26 in 0.75 dB steps
2
Optical AGC Range
dB
13
13
3
Module Responsivity
A/W dB
299 (High Gain)
49.5
299
49.5
4
A/W dB
67 (Standard Gain)
36.5
RF Frequency Response
dB
±0.5
±0.5
RF Test Point
dB
-20 (±1.0)
-20 (±1.0)
Return Loss
dB
> 16
> 16
Tilt
dB
+0.5 to -0.5
+0.5 to -0.5
Noise Equivalent Power
pA
Hz
< 8 (High Gain)
< 10 (Standard Gain)
< 2
Power Consumption
W DC
< 5
< 5
Notes
:
1. Reverse receiver (Rx) maximum output level is determined using 5 to 42 MHz noise
loading while ensuring that the link Noise Power Ratio (NPR) dynamic range is not Rx
limited. Rx RF attenuation may be needed to avoid exceeding maximum Rx output level
in operation. See Calculating Reverse Receiver RF Output Level on page 2.
limited. Rx RF attenuation may be needed to avoid exceeding maximum Rx output level
in operation. See Calculating Reverse Receiver RF Output Level on page 2.
2. RF Attenuation control: software control is via LCI, ICIM, or ROSA / TNCS.
3. Optical AGC range above and below nominal optical input power is determined by the
3. Optical AGC range above and below nominal optical input power is determined by the
initial RF attenuation setting. See Understanding Optical AGC Range on page 3.
4. Module responsivity is measured at 1310 nm with 0 dB RF attenuation, and may change
at other wavelengths.
Unless otherwise noted, specifications reflect typical performance and are referenced to the
ambient air temperature at the inlet to the Prisma II standard or Prisma II XD chassis.
Specifications are based on measurements made according to SCTE/ANSI standards (where
applicable), using standard frequency assignments.
ambient air temperature at the inlet to the Prisma II standard or Prisma II XD chassis.
Specifications are based on measurements made according to SCTE/ANSI standards (where
applicable), using standard frequency assignments.