Alpine dva-9965r User Manual
49
-EN
ALPINE DVA-9965R 68-02065Z31-A (EN)
Speaker Setup
The PXA-H700 or PXA-H701 can be set according to the playable
frequency range of your speakers.
Check the playable frequency range of the speakers (not including the
subwoofer) before performing this operation to verify whether the
speakers can play low frequencies (of about 80 Hz or less).
frequency range of your speakers.
Check the playable frequency range of the speakers (not including the
subwoofer) before performing this operation to verify whether the
speakers can play low frequencies (of about 80 Hz or less).
• Avoid stopping, pausing, switching the disc, cueing, fast-
forwarding or switching the audio channel of this unit while
making this adjustment. The setting is cancelled if Decode mode is
switched.
making this adjustment. The setting is cancelled if Decode mode is
switched.
1
Check that Defeat mode is off (page 22).
2
Press and hold MENU for at least 2 seconds.
3
Select the Speaker Setup mode by sliding your
finger on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the Speaker
Setup mode.
finger on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the Speaker
Setup mode.
4
Touch the GlideTouch bar, and select the speaker
by sliding your finger to the left or right, then press
the GlideTouch bar.
by sliding your finger to the left or right, then press
the GlideTouch bar.
5
Select the speaker characteristic by sliding your
finger on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the speaker
characteristic.
finger on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the speaker
characteristic.
OFF*
1
:
When no speaker is connected.
SMALL:
When a speaker that cannot play low
frequencies (80 Hz or less) is connected.
frequencies (80 Hz or less) is connected.
LARGE*
2
: When a speaker that can play low frequencies
(80 Hz or less) is connected.
*
1
It is not possible to set the front speakers to “OFF.”
*
2
If the front speakers are set to “SMALL,” the rear and
centre speakers cannot be set to “LARGE.”
centre speakers cannot be set to “LARGE.”
6
When the setting is complete, press and hold
MENU for at least 2 seconds.
MENU for at least 2 seconds.
• The subwoofer can be set only to ON/OFF.
• If the centre speaker is turned “OFF,” the centre channel’s audio
• If the centre speaker is turned “OFF,” the centre channel’s audio
signals are added to the audio signals output from the front
speakers.
speakers.
• If you set the speaker response to “OFF,” also set the speaker
setting to “OFF.” (page 46)
• Perform the setup for all the speakers (“Front,” “Center,” “Rear”
and “Subwoofer”). If not, the sound may not be balanced.
• When centre is set to “OFF”, the setting is ineffective even if
centre is set with this function.
• Through changing the settings on each speaker, a change in the
output of the other speakers may occur due to the setting
requirements.
requirements.
• When using the PRO LOGIC II, if the rear speaker is set to
“LARGE”, then there will be no output from the subwoofer.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 52.
9
Adjust the level by turning the Rotary encoder.
10
To adjust other bands, repeat steps 6 to 9.
11
When the setting is complete, press and hold
MENU for at least 2 seconds.
MENU for at least 2 seconds.
• When the speaker is set to the “OFF” mode, the parametric
equalizer for that speaker cannot be set. Refer to “Setting the
Speakers” (page 46).
Speakers” (page 46).
• It is not possible to adjust the frequencies of adjacent bands within
7 steps.
• Check the playable frequency ranges of the connected speakers
before making the equalizer adjustments. If the speaker’s playable
frequency range is 55 Hz to 30 kHz, for example, adjusting the
40 Hz or 20 Hz band has no effect. Additionally, you may overload
and damage the speakers.
frequency range is 55 Hz to 30 kHz, for example, adjusting the
40 Hz or 20 Hz band has no effect. Additionally, you may overload
and damage the speakers.
• When the parametric EQ is adjusted, the adjustment for graphic
EQ becomes ineffective.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 52.
Setting Bass Compressor
You can adjust the sound of low frequencies as desired.
1
Check that Defeat mode is off (page 22).
2
Press and hold MENU for at least 2 seconds.
3
Select the BASS COMP. mode by sliding your
finger on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the BASS COMP.
mode.
finger on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the BASS COMP.
mode.
4
Touch the GlideTouch bar, and select the desired
mode by sliding your finger to the left or right, then
press the GlideTouch bar.
mode by sliding your finger to the left or right, then
press the GlideTouch bar.
Bass sound is emphasized more as the mode is
sequentially switched as MODE1
sequentially switched as MODE1
→ 2 → 3, offering you
vivid low frequencies.
Select OFF when the setting is not necessary.
Select OFF when the setting is not necessary.
5
When the setting is complete, press and hold
MENU for at least 2 seconds.
MENU for at least 2 seconds.