Alpine dva-9965r User Manual
51
-EN
ALPINE DVA-9965R 68-02065Z31-A (EN)
6
Adjust the level by turning and then pressing the
Rotary encoder.
Rotary encoder.
The level can be adjusted within the range of –5 to +5.
The higher the level, the more the position of the centre
speaker is shifted to the sides.
The higher the level, the more the position of the centre
speaker is shifted to the sides.
7
When the setting is complete, press and hold
MENU for at least 2 seconds.
MENU for at least 2 seconds.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 52.
Achieving powerful high volume sound
(LISTENING)
(LISTENING)
With Dolby Digital, the dynamic range is compressed so that
powerful sound can be achieved at regular volume levels. This
compression can be cancelled to achieve an energetic sound with even
greater power, like the sound in a movie theatre.
This function works only in the Dolby Digital mode.
powerful sound can be achieved at regular volume levels. This
compression can be cancelled to achieve an energetic sound with even
greater power, like the sound in a movie theatre.
This function works only in the Dolby Digital mode.
1
Check that Defeat mode is off (page 22).
2
Press and hold MENU for at least 2 seconds.
3
Select the Multi CH setup mode by sliding your
finger on the GlideTouch bar to the left or right.
Press the GlideTouch bar
finger on the GlideTouch bar to the left or right.
Press the GlideTouch bar
under the Multi CH
setup mode.
4
Select the LISTEN MODE by sliding your finger on
the GlideTouch bar to the left or right. Press the
GlideTouch bar under the LISTEN MODE.
the GlideTouch bar to the left or right. Press the
GlideTouch bar under the LISTEN MODE.
5
Select the STD (Standard) or MAX (Maximum) by
sliding your finger on the GlideTouch bar to the
left or right. Press the GlideTouch bar under the
STD or MAX.
sliding your finger on the GlideTouch bar to the
left or right. Press the GlideTouch bar under the
STD or MAX.
STD: For powerful sound at regular volume levels
MAX: For powerful sound at high volumes
MAX: For powerful sound at high volumes
6
When the setting is complete, press and hold
MENU for at least 2 seconds.
MENU for at least 2 seconds.
• Keep the volume to a level at which sounds outside the vehicle can
still be heard.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 52.
Adjusting the DVD Level
The volume (signal level) for Dolby Digital, Dolby PL II, DTS and
PCM modes can be set.
PCM modes can be set.
• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
or switching the audio channel of this unit while making this
adjustment. The setting is cancelled if the Decode mode is switched.
adjustment. The setting is cancelled if the Decode mode is switched.
1
Check that Defeat mode is off (page 22).
2
Press and hold MENU for at least 2 seconds.
3
Select the DVD Level mode by sliding your finger
on the GlideTouch bar to the left or right. Press
the GlideTouch bar under the DVD Level mode.
on the GlideTouch bar to the left or right. Press
the GlideTouch bar under the DVD Level mode.
The DOLBY PL II setup mode is activated.
4
Press the GlideTouch bar to the left or right to
select the mode (DOLBY DIGITAL, DOLBY PL II,
DTS, PCM) to be adjusted.
select the mode (DOLBY DIGITAL, DOLBY PL II,
DTS, PCM) to be adjusted.
5
Adjust the level by turning the Rotary encoder.
The level can be adjusted in the range of –5 to +5.
6
When the other mode level is adjusted, press
MENU to return to the previous display, then
repeat steps 4 and 5.
MENU to return to the previous display, then
repeat steps 4 and 5.
7
When the setting is complete, press and hold
MENU for at least 2 seconds.
MENU for at least 2 seconds.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 52.
Using the Pro Logic II Mode
Pro Logic processing can be conducted on the music signals recorded on
two channels to achieve Dolby Pro Logic II surround sound. For two-
channel Dolby Digital and DTS signals, there is also a “REAR FILL”
function for outputting the signals of the front channel to the rear channel.
two channels to achieve Dolby Pro Logic II surround sound. For two-
channel Dolby Digital and DTS signals, there is also a “REAR FILL”
function for outputting the signals of the front channel to the rear channel.
1
Check that Defeat mode is off (page 22).
2
Press and hold MENU for at least 2 seconds.
3
Select the Dolby PL II mode by sliding your finger
on the GlideTouch bar to the left or right. Press
the GlideTouch bar under the Dolby PL II mode.
on the GlideTouch bar to the left or right. Press
the GlideTouch bar under the Dolby PL II mode.
The DOLBY PL II setup mode is activated.
4
Select the DOLBY PL II by sliding your finger on
the GlideTouch bar to the left or right, then press
the GlideTouch bar.
the GlideTouch bar to the left or right, then press
the GlideTouch bar.
5
Select the desired mode by sliding your finger on
the GlideTouch bar to the left or right. Press the
GlideTouch bar under the desired mode.
the GlideTouch bar to the left or right. Press the
GlideTouch bar under the desired mode.
PL II MOVIE:
Suits the stereo TV shows and all programs encoded
in Dolby Surround. It improves the sound field
directivity to near that of discrete 5.1-channel sound.
in Dolby Surround. It improves the sound field
directivity to near that of discrete 5.1-channel sound.
PL II MUSIC:
Can be used for all stereo music recordings, and
provides a wide, deep sound field.
provides a wide, deep sound field.
REAR FILL:
Depending on the input signals, the sound may only
be output from the front speakers. In this case, the
“REAR FILL” function can be used to output signals
from the rear speakers as well.
be output from the front speakers. In this case, the
“REAR FILL” function can be used to output signals
from the rear speakers as well.
OFF: Turns Dolby PL II function to OFF.
If PL II MUSIC is selected, the centre width can be adjusted
with the following operations.
with the following operations.
This function offers the optimum vocal position by adjusting
the centre channel position between the centre speaker and
the L/R speaker. (The adjustments established in “Adjusting
the acoustic image” (page 50) are ineffective while this
function is activated.)
the centre channel position between the centre speaker and
the L/R speaker. (The adjustments established in “Adjusting
the acoustic image” (page 50) are ineffective while this
function is activated.)
Continued