Manualsbrain.com
  1. Manuals
  2. Brands
  3. Alpine
  4. dva-9965r
  5. User Manual

Alpine dva-9965r User Manual

Download
Page of 76
52
-EN
ALPINE DVA-9965R 68-02065Z31-A (EN)
Selecting the CENTRE WIDTH CONT.
1) Select CENTER WIDTH by activating the DOLBY PL II
setup mode in step 4 of “Using the Pro Logic II Mode.”
2) Select ON or OFF by sliding your finger on the
GlideTouch bar to the left or right. Press the GlideTouch
bar under the ON or OFF.
If ON is set, you can enjoy the optimum vocal position
by distributing the centre channel sound between the
centre speaker and L/R speaker.
3) Adjust the level by turning the Rotary encoder.
The level can be adjusted between 0 to 7. When the
level increases, the centre channel position moves
from the centre speaker position to both sides.
6
When the setting is complete, press and hold
MENU for at least 2 seconds.
• This adjustment is ineffective when the speaker is set to CENTER
OFF in “Setting the Speakers” (page 46).
• This function only works with two-channel signals.  This operation is
ineffective when 5.1-channel DTS or Dolby Digital signals are input.
• If the REAR FILL setting is made while REAR MIX is ON, the
sound for rear fill is unchanged. REAR MIX is given priority
during all 2 channel decoding other than linear PCM.
• For linear PCM signals, the voice is output from the rear speaker
regardless of the REAR FILL and REAR MIX setting.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 52.
Linear PCM Setting
The output when playing discs recorded in linear PCM can be set to 2
or 3 channels.
1
Check that Defeat mode is off (page 22).
2
Press and hold MENU for at least 2 seconds.
3
Select the DVD Level mode by sliding your finger
on the GlideTouch bar to the left or right. Press
the GlideTouch bar under the DVD Level mode.
4
Select the PCM MODE by sliding your finger on the
GlideTouch bar to the left or right. Press the
GlideTouch bar under the PCM MODE.
5
Select the desired mode by sliding your finger on
the GlideTouch bar to the left or right. Press the
GlideTouch bar under the desired mode.
2CH OUTPUT: 2ch output (L/R)
3CH OUTPUT: 3ch output (L/R/CENTER)
6
When the setting is complete, press and hold
MENU for at least 2 seconds.
• This adjustment is ineffective when the speaker is set to CENTER
OFF in “Setting the Speakers” (page 46).
Storing Settings in the Memory
Up to 6 settings can be stored on the unit.
All settings and adjustments described below are stored in one
memory preset.
Setting/Adjusting items
Refer to page
Setting the Speakers
Setting Time Correction/Switching Phase
Adjusting EQ
Adjusting X-OVER
Setting MX
Setting BASS COMP.
Setting PRO LOGIC II/Adjusting the
Centre Width*
Adjusting Dolby Surround*
Linear PCM Setting*
46
47, 48
48, 49
46, 47
46
49
51, 52
50, 51
52
* Depending on the input signal, sound effect may not be obtained.
1
Press MENU.
2
Touch the GlideTouch bar, select AP Preset Mode
by sliding it to the left or right, then press
GlideTouch bar.
3
Touch the GlideTouch bar, select the preset
number (1 through 6) by sliding it to the left or
right, then press and hold the GlideTouch bar for
at least 2 seconds to store the adjusted contents.
• This function is operable only when Defeat is set to OFF.
• The stored contents will not be deleted even when battery power
cord is detached.
Getting out the Preset Memory
1
Check that Defeat mode is off (page 22).
2
Press MENU.
3
Touch the GlideTouch bar, select AP Preset Mode
by sliding it to the left or right, then press the
GlideTouch bar.
4
Touch the GlideTouch bar, and select a preset
number (1 through 6) you wish to recall by sliding
it to the left or right, then press the GlideTouch
bar.
•    It takes a few moment to get out the preset memory.