ATIKA asp 4-370 User Manual
Splitting logs:
¾
Always place the logs lengthwise and flat on the main frame
of the log splitter. The log must be enclosed by the log guide
plates. Fig. 7
of the log splitter. The log must be enclosed by the log guide
plates. Fig. 7
15
¾
Never place the log on the frame at an angle. Fig. 8
¾
Always ensure that the splitting wedge and the log ram
contact the ends of the log at right-angles.
contact the ends of the log at right-angles.
¾
Never try to split two logs at once.
¾
Never try to remove or replace the log during the splitting
process.
process.
L
Never try to force the splitting of the log by maintaining the
pressure for several seconds. This can lead to damage to the
machine.
Reposition the log on the main frame and repeat the splitting
process, or put the log to one side.
Reposition the log on the main frame and repeat the splitting
process, or put the log to one side.
How to release a jammed log?
1. Loose the operating lever as well as the operating pushbutton
that the log ram can go back.
1. Place a triangular wooden chock under the log, then move the
log ram forward so that it pushes the chock under the jammed
log.
2. If the log is not released, keep repeating this procedure, using
larger chocks, until the log is released.
Never use a hammer to release a jammed log, and keep
your hands away from the log.
Do not enlist the aid of a second person - this is a one-man job.
Do not try to release the log by using a hammer, since this may
break the motor block.
Do not enlist the aid of a second person - this is a one-man job.
Do not try to release the log by using a hammer, since this may
break the motor block.
Finishing work:
¾
Attend to that the log ram has gone back to its basic position.
¾
Then remove the plug from the power socket.
¾
Close the bleed screw. Fig. 3
¾
Follow the care and maintenance instructions.
Fig. 7
C
C
a
a
r
r
e
e
a
a
n
n
d
d
m
m
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
Remove the plug from the power socket before starting
any maintenance or cleaning work.
any maintenance or cleaning work.
Wear protective gloves in order to avoid injury to the hands.
L
Observe the following in order to keep the log splitter in
good working order:
good working order:
Clean the machine thoroughly after you have finished
using it.
using it.
Remove any resin remains on the machine.
Oil the piston rod (Fig. 1 / 2) regularly with an
environmentally friendly spray oil.
environmentally friendly spray oil.
Fig. 8
Check the oil level and change the oil as necessary.
Sharpening the splitting wedge
After extended periods of use, or if the splitting performance is
reduced, sharpen the splitting wedge with a file (and remove any
reduced, sharpen the splitting wedge with a file (and remove any
burrs). Fig. 9
Fig. 9
Sharpen wedge
How do I check the oil level?
1. The log ram must be in its starting position.
2. Stand the log splitter on end, with the filler opening at the top.
2. Stand the log splitter on end, with the filler opening at the top.
Fig 10
A second person will be required to up-end and hold
the log splitter.
3. Unscrew the dipstick – Fig. 11. Do not drop or lose the oil seal
when removing the dipstick.
4. Clean the dipstick and the oil seal.
5. Replace the dipstick fully into the oil reservoir.
6. Now remove the dipstick again, and read off the oil level.
5. Replace the dipstick fully into the oil reservoir.
6. Now remove the dipstick again, and read off the oil level.
If the oil level is between the two marking on the dipstick,
there is sufficient oil in the reservoir.
If the oil level is below the lower marking, more oil should
be added with the aid of a clean funnel.
lower marking upper marking
lower marking upper marking