Sony cdx-f7500 User Manual
34
Error displays/Messages
*1
When the CD/MD changer is connected to the unit,
the disc number of the CD or MD appears in the
display.
the disc number of the CD or MD appears in the
display.
*2
The disc number of the disc causing the error
appears in the display.
appears in the display.
Radio reception
Preset tuning is not possible.
• Store the correct frequency in the memory.
• The broadcast signal is too weak.
• The broadcast signal is too weak.
The stations cannot be received.
The sound is hampered by noises.
The sound is hampered by noises.
• Connect a power aerial control lead (blue) or
accessory power supply lead (red) to the
power supply lead of the car’s aerial booster.
(Only if your car has a built-in FM/MW/LW
aerial in the rear/side glass.)
power supply lead of the car’s aerial booster.
(Only if your car has a built-in FM/MW/LW
aerial in the rear/side glass.)
• Check the connection of the car aerial.
• The auto aerial will not go up.
• The auto aerial will not go up.
t Check the connection of the power aerial
control lead.
• Check the frequency.
• When the DSO mode is on, the sound is
• When the DSO mode is on, the sound is
sometimes hampered by noises.
t Set the DSO mode to “OFF” (page 27).
t Set the DSO mode to “OFF” (page 27).
Automatic tuning is not possible.
• The local seek mode is set to “on.”
t Set the local seek mode to “off”
(page 26).
• The broadcast signal is too weak.
t Perform manual tuning.
The “ST” indication flashes.
• Tune in the frequency accurately.
• The broadcast signal is too weak.
• The broadcast signal is too weak.
t Set to the monaural reception mode
(page 26).
A programme broadcast in stereo is heard
in monaural.
in monaural.
The unit is in monaural reception mode.
t Cancel monaural reception mode
(page 26).
RDS
The Seek starts after a few seconds of
listening.
listening.
The station is non-TP or has weak signal.
t Press (AF/TA) on the unit repeatedly until
t Press (AF/TA) on the unit repeatedly until
“AF, TA-off” appears.
No traffic announcements.
• Activate “TA.”
• The station does not broadcast any traffic
• The station does not broadcast any traffic
announcements despite being TP.
t Tune in another station.
t Tune in another station.
PTY displays “- - - - - - - -.”
• The current station is not an RDS station.
• RDS data has not been received.
• The station does not specify the programme
• RDS data has not been received.
• The station does not specify the programme
type.
Error displays
(For this unit and optional CD/MD changers)
The following indications will flash for about 5
seconds, and an alarm sound will be heard.
seconds, and an alarm sound will be heard.
Blank
*
1
No tracks have been recorded on an MD*
2
.
t Play an MD with recorded tracks on it.
Error
*
1
• A CD is dirty or inserted upside down*
2
.
t Clean or insert the CD correctly.
• A CD/MD cannot play because of some
problem*
2
.
t Insert another CD/MD.
Failure
The connection of speakers/amplifiers is
incorrect.
t See the installation guide manual of this
incorrect.
t See the installation guide manual of this
model to check the connection.
High Temp
The ambient temperature is more than 50°C.
t Wait until the temperature goes down
t Wait until the temperature goes down
below 50°C.
NO Disc
*
1
No disc is inserted in the CD/MD unit.
t Insert discs in the CD/MD unit.
t Insert discs in the CD/MD unit.
NO Magazine
The disc magazine is not inserted in the CD
unit.
t Insert the magazine in the CD unit.
unit.
t Insert the magazine in the CD unit.
NO Music
*
2
A CD which is not a music file is inserted in
the MP3 playable CD unit.
t Insert a music CD in the MP3 playable CD
the MP3 playable CD unit.
t Insert a music CD in the MP3 playable CD
unit.
Offset
There may be an internal malfunction.
t Check the connection. If the error
t Check the connection. If the error
indication remains on in the display,
consult your nearest Sony dealer.
consult your nearest Sony dealer.
Push Reset
The CD/MD unit cannot be operated because
of some problem.
t Press the RESET button on the unit.
of some problem.
t Press the RESET button on the unit.