Sony GDM-F400
14
Sony GDM-F400/F500 (E,F,S,C2) 3-864-156-22 (1)
Additional settings (OPTION)
You can manually degauss (demagnetize) the monitor, change the
menu position, set the power saving delay time, and lock the
controls.
menu position, set the power saving delay time, and lock the
controls.
1
Press the joystick.
The main MENU appears on the screen.
2
Move the joystick to highlight
OPTION and press
the joystick again.
The OPTION menu appears on the screen.
3
Move the joystick to highlight the desired
adjustment item.
adjustment item.
Adjust the selected item according to the following
instructions.
instructions.
Degaussing the screen
The monitor is automatically demagnetized when the power is
turned on.
turned on.
To manually degauss the monitor, first move the
joystick up or down to select
joystick up or down to select
(MANUAL DEGAUSS).
Then move the joystick to the right.
The screen is degaussed for about 3 seconds. If a second degauss
cycle is needed, allow a minimum interval of 20 minutes for the
best result.
cycle is needed, allow a minimum interval of 20 minutes for the
best result.
Changing the menu’s position.
Change the menu’s position if it is blocking an image on the
screen.
screen.
To change the menu’s on-screen position, first move
the joystick up or down to select
the joystick up or down to select
(OSD H POSITION)
for horizontal adjustment, or
(OSD V POSITION) for
vertical adjustment. Then move the joystick to the left
or right to shift the on-screen menu.
or right to shift the on-screen menu.
Changing the power saving delay time.
To adjust the time it takes to enter the power saving
mode, first move the joystick up or down to select
mode, first move the joystick up or down to select
(PWR SAVE DELAY). Then move the joystick to the left
or right to select the desired time.
or right to select the desired time.
If you select OFF, the monitor does not enter power saving mode.
See page 15 for more information about the monitor’s power
saving capabilities.
See page 15 for more information about the monitor’s power
saving capabilities.
Locking the controls.
To protect adjustment data by locking the controls, first
move the joystick up or down to select
move the joystick up or down to select
(CONTROL
LOCK). Then move the joystick to the right to select
LOCK.
LOCK.
Only the
1 (power) switch, EXIT, and
(CONTROL LOCK)
of the
OPTION menu will operate. If any other items are
selected, the
mark appears on the screen.
To cancel the control lock
Repeat the procedure above and set
(CONTROL LOCK) to
UNLOCK.
Resetting the adjustments
This monitor has the following three reset methods. Use the
RESET button to reset the adjustments.
RESET button to reset the adjustments.
Resetting a single adjustment item
Use the joystick to select the adjustment item you want to reset,
and press the RESET button.
and press the RESET button.
Resetting all of the adjustment data for the
current input signal
current input signal
Press the RESET button when no menu is displayed on the screen.
Note that the following items are not reset by this method:
• on-screen menu language (page 8)
• on-screen menu position (page 14)
• power saving delay time (page 14)
• control lock (page 14)
Note that the following items are not reset by this method:
• on-screen menu language (page 8)
• on-screen menu position (page 14)
• power saving delay time (page 14)
• control lock (page 14)
Resetting all of the adjustment data for all input
signals
signals
Press and hold the reset button for more than two seconds.
Note
The RESET button does not function when
(CONTROL LOCK)
is set to LOCK.
ZZ...
RESET
GDM-F500.book Page 14 Friday, December 4, 1998 3:55 PM